Seven rainbow h81btc settings
Publish: 2021-04-16 09:09:19
1. 1. How much is the power supply
2. Whether it can be turned on normally under the test of other computer configuration
2. Whether it can be turned on normally under the test of other computer configuration
2. 1. This does not need too many settings, the best graphics card is to use NV graphics card
2, the system win10, the power supply is enough, the latest version of BIOS on the motherboard, the BIOS is set as the main graphics card for the PCIe
2, the system win10, the power supply is enough, the latest version of BIOS on the motherboard, the BIOS is set as the main graphics card for the PCIe
3. 1. The hard disk must be in GPT format and the system must be 64 bit. UEFI does not support 32-bit system
note: strictly speaking, UEFI can also boot x64 system on MBR disk, but special settings should be made. This is the general situation
2. The traditional MBR partition only supports 2.2t hard disk, and the hard disk larger than 2.2t needs GPT, otherwise it will be wasted; Microsoft operating system supporting UEFI startup: all 64 bit systems after Windows Vista SP1
3. Installation requirements: the installation media must start the computer in UEFI mode. Cut! A lot of people die at this stage. If you start the installation program as before, there will be an error prompt that you cannot install to the GPT partition, which will cause the installation failure
① turn on UEFI mode in BIOS
② the installation media supports UEFI startup
③ for Windows 7 and its previous systems, when using U disk or mobile hard disk to install, how to add UEFI support files:
extract bootmgfw.efi file from Windows 8 installation file, rename it as bootx64.efi, and it to # 92 of win7 installation file; EFI\ Boot\ Next, there is no new boot folder
bootmgfw.efi can also be obtained from the installed win8 system
④ when the first two conditions are met, the U disk or mobile hard disk boot item marked with "UEFI" will appear in the boot menu. Select this item to "start the computer in UEFI mode"!
note: strictly speaking, UEFI can also boot x64 system on MBR disk, but special settings should be made. This is the general situation
2. The traditional MBR partition only supports 2.2t hard disk, and the hard disk larger than 2.2t needs GPT, otherwise it will be wasted; Microsoft operating system supporting UEFI startup: all 64 bit systems after Windows Vista SP1
3. Installation requirements: the installation media must start the computer in UEFI mode. Cut! A lot of people die at this stage. If you start the installation program as before, there will be an error prompt that you cannot install to the GPT partition, which will cause the installation failure
① turn on UEFI mode in BIOS
② the installation media supports UEFI startup
③ for Windows 7 and its previous systems, when using U disk or mobile hard disk to install, how to add UEFI support files:
extract bootmgfw.efi file from Windows 8 installation file, rename it as bootx64.efi, and it to # 92 of win7 installation file; EFI\ Boot\ Next, there is no new boot folder
bootmgfw.efi can also be obtained from the installed win8 system
④ when the first two conditions are met, the U disk or mobile hard disk boot item marked with "UEFI" will appear in the boot menu. Select this item to "start the computer in UEFI mode"!
4. You can use the latest BIOS on the official website.
the settings have been adjusted in the new BIOS. There are operation steps in DOS. You can refer to the following
Mining graphics card to install a driver. Mining generally uses the same chip graphics card
the settings have been adjusted in the new BIOS. There are operation steps in DOS. You can refer to the following
Mining graphics card to install a driver. Mining generally uses the same chip graphics card
5. Modification method:
when the computer is turned on, press del key to enter the main board BIOS, press F7 - OK to enter the advanced mode, select AI tweeter - select (memory frequency) - open, select 1600, OK - press F10 to save.
when the computer is turned on, press del key to enter the main board BIOS, press F7 - OK to enter the advanced mode, select AI tweeter - select (memory frequency) - open, select 1600, OK - press F10 to save.
6. The data cable of the monitor should be connected to the single display interface. Press the F2 or del key to enter the BIOS when starting up.
7. Insert the U-disk which has been made by u-qiwang U-disk installation system tool into the USB socket on the computer (it is recommended to insert the U-disk directly into the USB socket on the back of the computer host, so that the transmission performance will be better), and then turn on the computer
after turning on the computer, when you see the power on screen, press & quot; F12" Key will enter a window to select the order of startup items
after entering, move the cursor to the selected place and display it as & quot; USB" After selecting the startup options, you only need to press enter to enter the main interface of u-king!
after turning on the computer, when you see the power on screen, press & quot; F12" Key will enter a window to select the order of startup items
after entering, move the cursor to the selected place and display it as & quot; USB" After selecting the startup options, you only need to press enter to enter the main interface of u-king!
8.
-
after the computer is turned on, when you see the power on screen, press & quot; ESC or F11 & quot; Key
-
the default option is U disk startup, so we can directly press enter to enter U disk startup
< / OL >
9. Try to take the motherboard out of the chassis, bare metal try, and then can't use the replacement method to replace the power motherboard or something
10.
The hard disk boot has been set as an example:
1. Turn on the computer and wait for the boot screen to appear. Press the "delete" key to enter the home page of BIOS settings of Qicaihong motherboard.
Hot content