BTC wallet cannot be opened after forced shutdown

1. It's OK. Just take out the wallet file and reload it. If you don't log in bitcoin, you'll get it

2. Search: black soul 3's damage calculation is addition and subtraction or multiplication, which master knows the calculation formula

3. I personally use the sum hardware wallet, and then mine through jiajiabao intelligent robot, which can dig 8 kinds of coins and store them in the sum hardware wallet, which is convenient and safe.

4. I'm very happy to answer for you.
- - - - - -
Hello, you can try to refresh. If you can't get in many times, you can login QQ again< There are many problems when you can't open your wallet.
1. Problems with your own computer.
viruses in your computer or computer network card (you should kill viruses frequently if you have viruses, and wait patiently for the card to refresh)
2. Tencent's system problems
-

if you are satisfied with my answer, Please click "adopt as the answer" below for encouragement, thank you.

5.

Step 1: first of all, check whether the external wiring of the computer is well connected, and plug in all the wiring again to see if the fault is eliminated

Step 2: if the fault still exists, open the mainframe box to check whether there is any rendant metal in the chassis, or the short circuit caused by the deformation of the main board, smell whether there is burnt paste in the chassis, whether there are burnt chips on the main board, and whether the capacitors around the CPU are damaged

Step 3: if not, clean the st on the motherboard, and then check whether the computer is normal

Step 4: if the fault persists, then unplug the reset cable, other switches and indicator lights on the motherboard, and use the short circuit switch with a screwdriver to see if it can be turned on

Step 5: if the computer can't be turned on, then use the minimum system method to unplug the data cables of hard disk, floppy disk drive and optical disk drive, and then check whether the computer can be turned on. If the boot screen appears on the computer display, it means that the problem lies in these devices

Step 6: if the fault still exists, the fault may be caused by memory, graphics card, CPU, motherboard and other devices. Then use the plug-in method, exchange method and other methods to check the memory, graphics card, CPU and other devices are normal, if there is a damaged device, replace the damaged device

Step 7: if the memory, graphics card, CPU and other devices are normal, then discharge the BIOS, use the isolation method, place the motherboard outside the chassis, connect the memory, graphics card, CPU and other devices for testing, if the computer can display, then install the motherboard into the chassis for testing until the cause of the failure is found. If the fault still exists, return the motherboard to the manufacturer for repair

Step 8: when the computer is turned on, there is no display but an alarm sound. When the computer is turned on, the system BIOS starts to perform post (power on self-test). When a fatal error is detected in a device in the computer, it controls the loudspeaker to make a sound to report the error. Therefore, there may be no display and alarm sound when the machine is started

6. Because the network is not good

7. I think the system file of the computer is damaged, so I suggest that the operating system be reinstalled< The specific steps are as follows: select drive letter C in my computer, right-click to select properties, select "tools → start checking" in the pop-up drive properties window, select "automatically repair file system errors" and "scan and recover bad sectors", and then click start, The scanning time will vary with the disk capacity and scanning options (after doing the above method, a box will pop up, click Yes, repair after auto shutdown, and select the scheled disk check button for win78)

the bad track of hard disk will lead to the damage or loss of computer system files, and the computer can not start or crash. The bad track of hard disk can be repaired by NDD disk tool or ScanDisk

if the fault still exists, please restore the system or reload it (or you can't format the hard disk, re partition and reload it; if you can't, you'll have to change the hard disk, or overhaul it).

8. This is the disk damage caused by illegal shutdown or other reasons. Please repair it (each disk is repaired or only C and f disks are repaired)<

disk repair method of the system:
the specific steps are as follows: select drive letter C in my computer, right-click to select properties, select "tools → start checking" in the pop-up drive properties window, select "automatically repair file system errors" and "scan and recover bad sectors", and then click start, The scanning time will vary with the disk capacity and scanning options (after doing the above method, a box will pop up, click Yes, repair after auto shutdown, and select the scheled disk check button for win78)

the bad track of the hard disk will cause the computer system files to be damaged or lost, and the computer will be unable to start or crash. The bad track of hard disk can be repaired by NDD disk tool or ScanDisk

if the fault persists, please restore the system or reload it (or you can't format the hard disk, re partition and reload it, or you have to change the hard disk if you can't, or you can repair it).

9. 1) It is suggested to turn off the automatic update, use the software update, and make your own time. Download super rabbit and ask her to help you download the patch. After you select quick detection, press the Install button, and it will automatically help you download and install without restarting. So far, using super rabbit to patch has been successful (for the system, you don't need to install all patches, so super rabbit has fast detection (recommended), comprehensive detection, and customization. Choose fast detection, and only install patches that have serious security vulnerabilities on the system. The antivirus and Trojan killing software you use all have this function)<

how to turn off automatic updates:

control panel - Windows Update - (left) change settings - change the option under Important updates to never check for updates (win7)

this method can also be used, please start / run, enter gpedit.msc to open the group policy, select user configuration / management template / windows components / Windows Update / on the left, select "delete access using all windows update functions" on the right, double-click it, select "enabled" in the open dialog box, and then confirm by application to restart the computer

2) if it is not caused by the above problem:

this is the disk damage caused by illegal shutdown or other reasons, please repair it (repair each disk or only repair C)<

disk repair method of the system:
the specific steps are as follows: select drive letter C in my computer, right-click to select properties, select "tools → start checking" in the pop-up drive properties window, select "automatically repair file system errors" and "scan and recover bad sectors", and then click start, The scanning time will vary with the disk capacity and scanning options (after doing the above method, a box will pop up, click Yes, repair after auto shutdown and select the scheled disk check button for win7)

the bad track of the hard disk will cause the computer system files to be damaged or lost, and the computer will be unable to start or crash. The bad track of hard disk can be repaired by NDD disk tool or ScanDisk

if the fault persists, please restore the system or reload it (or you can't format the hard disk, re partition and reload it, or you have to change the hard disk if you can't, or you can repair it).