1. Yingtai tb250-btc is a B250 chipset, which can only use DDR4 memory, and does not support ddr31600
to play CF underground city, you'd better change to a better CPU. You can use g4560, because the performance of g4400 is too poor
2. This starts from the verification of the system. In fact, when installing the graphics card driver, the driver needs to independently verify each graphics card, and every time a graphics card is installed, the driver needs to compare it, so as to correct the graphics card and make it achieve the most ideal working condition. In this way, once you install more than one graphics card at a time, it will lead to a long verification process, and ring the verification, it will cause flicker, huge power consumption of the graphics card, and even system crash. Therefore, you need to install the driver one by one.
3. The steps are as follows:
1. Right click the properties of my computer and click the control panel home page
4. I don't know what you mean by "plug in directly". It's better not to plug in the power on state. The graphics card doesn't support hot swap. Be careful to burn it. The situation you said may be: 1. The graphics card needs external power supply. You didn't plug it in, so the graphics card can't be recognized. 2 motherboard power shortage, graphics card does not work, such as the use of not 24 pin power will lead to this result. Integrated graphics card board and then install the motherboard generally do not need to set BIOS, plug in can identify, at least can boot, display can be bright. After entering the system, the driver needs to be refitted. In BIOS, display into is generally automatic.
5. Uninstall the original motherboard and graphics card driver
power off
unplug the graphics card
plug in the graphics card
power on
prompt to find new hardware
install the driver (first install the motherboard and then install the graphics card)
Restart
OK
6. Remove the problem of the graphics card itself (try to change the computer)... Remove the problem of dirty interface and poor contact of the motherboard graphics card (use the eraser golden finger)... And then remove the setting of the main display in the BIOS (however, generally the BIOS is inserted with the main display, the default is the main display).
there is a problem with your motherboard
7. Can I see the post screen? If you can, enter the BIOS to set it, let your new graphics card as a picture output device to save and restart
8. Generally speaking, as long as there is PCI-E x16 expansion slot on the motherboard, it can be installed with independent graphics card, but there are also a few graphics cards because of compatibility problems, which also repel graphics card
1. For some very old motherboards, such as G41 motherboard, the CPU is also limited by the motherboard because the components of the motherboard are relatively low-end. Now that kind of high-end graphics card (such as fine gtx960, or ASUS gtx970) simply can not afford, or compatibility is not good. In this case, it is necessary to choose a relatively low-end graphics card, such as PCI-E 2.0 graphics card, such as hd6570
2. For example, H61 motherboard is incompatible with some types of graphics cards. Such as PCI-E 3.0 graphics card in H61 motherboard sometimes will not light or incompatible
in short, if the motherboard doesn't recognize the independent graphics card, you can re install the motherboard system for adjustment. If it doesn't work after re installing the system, you have to replace another model of graphics card.
9. -
check whether the monitor cable is connected to the independent graphics card. You can see that the graphics card is not installed properly at the back of the chassis. After the computer is shut down, pull out the independent graphics card again, wipe it off and insert it again (all the gold fingers should be inserted)
-
it is very likely that the cloned version of the system installed on the motherboard is not fully driven, You can use the driver wizard software. After driver detection, you can install the driver to be upgraded or optimized, and then download the independent graphics card driver from the official website of the corresponding brand. After installing the system of the installation version, you can manually play the motherboard driver one by one. Finally, you can install the independent graphics card driver on the official website of the corresponding brand, and restart the use of
< / OL >
10. My motherboard is ms-7131, and the independent graphics card installed is ati-9518 ice wing AGP 8x, but it can't show anything! Another question: does ms-7131 BIOS have any special settings? Add: what I said is that after the graphics card is inserted into the motherboard, there is no display on the display. But the integrated graphics card can be used again! What do you mean by "unrecognizable" on February 14, 2010? Can't install driver or don't display output? Add: is your display interface plugged into the signal output terminal of the independent graphics card? After the motherboard is plugged in, the integrated graphics card will be automatically shielded, so don't plug in the output of the motherboard, plug in the output of the display. Ask: tried! Independent graphics card did not reflect! Is it related to the BIOS of the motherboard? Answer: not necessarily. First of all, you need to make sure that your graphics card is in good condition, and then you need to consider the setting of the motherboard. Generally, the display only needs to be plugged in. If necessary, you can check the instructions of the motherboard.
