BTC clutch
Publish: 2021-04-20 00:30:36
1. 1. The connection between teeth is small in volume, but the torque transmitted is several times of other equal volumes
2. There is no slip and torque loss in 1:1 constant value transmission
3. The connection or separation is instantaneous and quick
4. The integrated structure is easy to install without worrying about the tooth contact axis
5. It needs to be connected at low speed, but it can run at high speed
6. It can be used either dry or wet.
2. There is no slip and torque loss in 1:1 constant value transmission
3. The connection or separation is instantaneous and quick
4. The integrated structure is easy to install without worrying about the tooth contact axis
5. It needs to be connected at low speed, but it can run at high speed
6. It can be used either dry or wet.
2. 1. Implicated rotation of cylinder
the implicated rotation of cylinder and piston e to the action of bearing is fixed or stopped by three 45 degree grooves or Z-M threads. But to stop properly, not because of the external interference force to make the cylinder deviation, oblique and abnormal work
2. Pay attention when installing the clutch on the shaft
when installing the clutch on the shaft, use special tools to pressurize the hollow shaft tube as far as possible, and do not impact the cylinder or other vulnerable parts
3. Installation of shaft end of pulley and gear
the radial force center of pulley or gear shall be aligned with the bearing center of two groups of bearings inside the flange as far as possible. Excessive offset will affect the service life of the proct
4. Bearing related
generally, the sealed bearing is maintenance free, and a few parts need to be properly supplemented with grease according to the relationship between the use environment, usually 1 to 6 months
5. Avoid overload operation
the safety factor of 1.5 to 2 times of the torque should be adopted as far as possible in proct selection, which will cause damage to the tooth surface or rece the service life
the above are matters needing attention. If you are helpful, please adopt them. Thank you
the implicated rotation of cylinder and piston e to the action of bearing is fixed or stopped by three 45 degree grooves or Z-M threads. But to stop properly, not because of the external interference force to make the cylinder deviation, oblique and abnormal work
2. Pay attention when installing the clutch on the shaft
when installing the clutch on the shaft, use special tools to pressurize the hollow shaft tube as far as possible, and do not impact the cylinder or other vulnerable parts
3. Installation of shaft end of pulley and gear
the radial force center of pulley or gear shall be aligned with the bearing center of two groups of bearings inside the flange as far as possible. Excessive offset will affect the service life of the proct
4. Bearing related
generally, the sealed bearing is maintenance free, and a few parts need to be properly supplemented with grease according to the relationship between the use environment, usually 1 to 6 months
5. Avoid overload operation
the safety factor of 1.5 to 2 times of the torque should be adopted as far as possible in proct selection, which will cause damage to the tooth surface or rece the service life
the above are matters needing attention. If you are helpful, please adopt them. Thank you
3. 1. BTC clutch is connected by two plane gear discs moving axially ring ventilation, and automatically separated by return spring ring pressure relief
2. BTC type toothed pneumatic clutch transmits power for the connection of toothed teeth, so there is no slip and the power transmission is exquisite. It can be used in narrow space with a wide range of torque from 0.01kgf. M to 16600kgf. M.
3. The connection between teeth is small in volume, but the torque transmitted is several times of other equivalent volumes
4. There is no slip and torque loss in 1:1 constant value transmission
5. The connection or separation is instantaneous and quick
6. The integrated structure is easy to install without worrying about the tooth contact axis
7. It needs to be connected at low speed, but it can run at high speed
8. It can be used either dry or wet.
2. BTC type toothed pneumatic clutch transmits power for the connection of toothed teeth, so there is no slip and the power transmission is exquisite. It can be used in narrow space with a wide range of torque from 0.01kgf. M to 16600kgf. M.
3. The connection between teeth is small in volume, but the torque transmitted is several times of other equivalent volumes
4. There is no slip and torque loss in 1:1 constant value transmission
5. The connection or separation is instantaneous and quick
6. The integrated structure is easy to install without worrying about the tooth contact axis
7. It needs to be connected at low speed, but it can run at high speed
8. It can be used either dry or wet.
4. Working principle of BTC:
BTC toothed clutch is connected by two plane toothed discs moving axially to the inside ring ventilation, and automatically separated by return spring ring pressure relief.
BTC toothed clutch is connected by two plane toothed discs moving axially to the inside ring ventilation, and automatically separated by return spring ring pressure relief.
5. You can use Handong clutch. Their BTC / BDC / HBS are suitable for special vehicles, and the quality is OK
6. The types of pneumatic clutches made by this company include standard through shaft clutch NAC, toothed through shaft clutch BTC, multi plate through shaft clutch BDC, inner tooth through shaft clutch HBS, gear through shaft clutch HTP, pneumatic drum clutch ah sh, pneumatic clutch NAC type nac-2, nac-5, nac-10, nac-20, nac-40, nac-60, toothed through shaft clutch BTC type btc-10, Btc-20, btc-40, btc-60, btc-80, etc. multi plate through shaft clutch BDC type has bdc-40, bdc-60, bdc-80, bdc-100, etc.
7. Which vehicle are you using? Han Dong's BDC, HBS and BTC models can be used
8. There are two types of pneumatic clutch, which are servo type and gas-liquid mixed type, and they are widely used
9. Instrial clutch brake has sh series drum brake, ah type drum brake, which can be used in large instrial equipment. Instrial clutch has pneumatic clutch, NAC type, BDC type, BTC type, HTP type. Instrial brake has through axle brake, nab type
10. Handong pneumatic clutch is connected by air pressure and released by return spring. Specifically, when the power supply of the solenoid valve is turned on, the compressed air enters the air chamber of the cylinder through the air guide tap, and the piston moves axially to push the friction plate, the intermediate disc and the belt pulley plane to press together. If the air pressure rises graally, the working machine will be soft started to achieve stable operation. When the solenoid valve is closed, the air pressure disappears, and the friction plate will be completely separated by the quick return of the spring.
Hot content