Yingtai b250btcm2 interface

1. Yingtai tb250-btc D + motherboard is a mining professional board. Why separate power supply for each of the pcies? This is because a single interface power supply is not enough. With so many independent graphics cards, it is necessary to plug them separately. This is designed for the stable use of multiple graphics cards,

2. It's just a hard disk. You can use it if you want. What's not recommended

3. Yingtai tb250-btc D + motherboard is a mining motherboard. The miner needs a special power supply. The output ports all use 6pin interface, all of which are 12V output. The 5V and 3.3V power supply interfaces in 24pin are canceled. The motherboard belongs to a professional application board, so it is not suitable for ordinary PC host power supply, so it needs to use a special 6pin 12V full interface power supply. Such as: quanhan fsp1600w rated power mining special power supply.

4. B250 itself supports the M2 interface. Although adding m2 to the feeder board is unnecessary, you can transfer the PCI X4 channel from m2 to the graphics card. Mining only relies on GPU general-purpose computing, and has low performance requirements for hard disk and CPU
however, to play mining, it is recommended to buy a more efficient ant miner instead of a graphics card. The graphics card is only a general-purpose calculation, not a specific one. The ant miner has higher efficiency and lower power consumption.

5. Because now many people choose solid-state hard disk to install,
although mining does not need a large capacity storage device, it is not bad to use a small capacity solid-state hard disk, and the whole mining system will run more efficiently.

6. The motherboard adopts lga1151 pin and supports the sixth or seventh generation of lga1151 interface processor.

7. There is no need to
the cheap small capacity is enough
it is not worth buying the expensive one
it has no direct relationship with the mining capacity

8.

(1) Solid state disk with nvme support

(2) the scale of B5 series is lower than that of z7 and H7 series, but the advantage lies in the sufficiency and price, so it's natural to sell well. B250 chipset is equipped with an m.2 SSD interface as standard, but in fact, e to the popularity and rapid development of m.2 SSD, many manufacturers will use the chipset bus to design an m.2 SSD interface for the motherboard, although many people may not use it. As for USB 3.1 in the generation of 200 series, it is still not native support, and all manufacturers need to borrow chips from third-party manufacturers to expand

9. 1. Installation foolishness - double click installation
now hardware manufacturers have paid more and more attention to the humanization of their procts, including simplifying the installation of drivers as much as possible, so many drivers have an "setup.exe" executable file. Just double click it and then "next" all the way to complete the installation of drivers. Some hardware manufacturers provide the driver CD-ROM with autorun self boot file. As long as the CD-ROM is put into the computer's CD-ROM drive, the CD-ROM will start automatically. Then click the corresponding driver name in the startup interface to start the installation process automatically. This humanized design makes it very convenient to install the driver.

2. Specify the installation from the device manager.
What if there is neither autorun self startup nor "setup. Exe" installation executable file in the driver file? At this time, we need to specify the driver file and install it manually

we can specify the location of the driver from the device manager and then install it. Of course, this method needs to prepare the driver to be installed in advance, and this method is also applicable to update the new version of the driver

first enter "system properties" from the control panel, and then click "hardware" - Device Manager

there will be an exclamation mark "!" in front of the device without driver installed Mark

right click the device, and then select "update driver"

a "hardware update wizard" will pop up. Now that we know what type of device it belongs to and its driver, we can select "install from list or location"

if the driver is on a CD or floppy disk, just tick "search for removable media" in the pop-up window. If it is on a hard disk, tick the check box in front of "include this location in search", and then click "Browse". Then find the driver folder we have prepared. It should be noted that many hardware manufacturers will suppress many types of hardware device drivers in one disk, and there will be different operating system versions, such as for Win2K (WIN2000) and for WinXP. Pay attention to choose the correct device and operating system version. After you click OK, click next

then we will find the driver folder we have prepared. Sometimes there will be multiple devices in it, and there will be different operating system versions, such as for Win2K (WIN2000) and for WinXP. Pay attention to choose the correct device and operating system version. After you click OK, click next. After a while, you can finish installing the device driver

3. Let windows automatically search for drivers
as we said earlier, advanced operating systems support plug and play, so when we install a new device, we start the computer. When the computer enters the operating system (such as windows), if the hardware device installed by the user supports plug and play function, then ring the process of starting the computer, The system will automatically detect new devices. When Windows detects new hardware devices, the "find new hardware wizard" dialog box will pop up

first of all, we can try to let it install the driver automatically, select "auto install software", and then click "next". If the operating system contains the driver of the device, the operating system will install it automatically, and we will complete the task. If not, the hardware device cannot be installed

at this time, we have to specify the location of the driver file ourselves. Click "back" to return to the "find new hardware wizard" dialog box. Then select Install from list or specified location, and then click next

the next steps are the same as using the "hardware update wizard" of device manager. You can specify the location of the driver and then install it.

10. Most drivers need to be decompressed before installation. You try to insert the drive CD into the CD-ROM drive, unzip the video card driver, and then start to install it; Right click my computer - properties - hardware - Device Manager - double click the graphics card - re install the driver - select 'this time only' and then click 'next' - select 'install in list or specified location (Advanced)' and click 'next' - select 'include this location in search', Click Browse / to find the video card driver after download and decompression, click OK, click Next / to start the installation, finish and close