Firmware of Bihu blockchain router

1. You can brush it, but you have to find out whether the firmware board can be used, or it will become a brick, which will be useless.

2. Methods / steps

1
first, we connect the device to set the mobile app, download the mobile app, click to enter the setting interface, and enter the default password admin to set the router

2
then type in the router name and password, click next, and wait about 20 seconds to complete the basic settings of the router and enter the main interface

3
My routing mole is divided into four small moles, namely terminal management, network speed test, signal strength and router setting
the overall feeling is clear-cut, but when I really use it, I find that if I want to use these functions, I need to have a registered account to log in. OK, I'll take it

4
after binding the mobile phone, enter the terminal management interface to display the mobile terminal connected to the router. You can view the real-time network speed of the access terminal, speed limit it and pull it into the blacklist. The network speed test mole can test the network speed, intuitive and clear understanding of their own network speed

5
the signal strength interface can set the signal strength of the router, including three modes. Of course, the greater the signal strength, the stronger the radiation. Users can adjust it according to their own needs

end
method / step 2

1
router setting interface, the user can set the password of the router, and also can count the status and working hours of the router, so the operation is simple

2
the intelligent plug-in mole can set the time switch for wireless, and the sleep time can be automatically turned off to ensure health, further optimize the network settings and improve the network speed
in general, the mobile app is easy to operate and user-friendly. Let's continue to look at the situation of setting on the PC

end
method / step 3

1
open the PC browser, type 192.168.62.1, enter the setting interface, and enter the password admin

2
it's very simple to enter the main interface. Compared with mobile app, it has no more functions. Even less than the app function on the mobile terminal, the advanced intelligent function is completed on the mobile terminal

3. Hello, this USB interface can share some resources through the LAN. Whether it can brush the third-party firmware depends on the specific scheme of the router and whether the third-party firmware is available; This kind of router and NAS are far worse than that. The router with more than 100 yuan has no comparable performance or function with professional NAS.

4. Today's routers are all intelligent routers. There is one more thing that we like to toss about. Brushing the third-party firmware to the router can make the router have functions that it didn't have before< More

tools / raw materials; Router & 160; Third party routing firmware; Before we start, let's talk about the whole process of swipe in: first swipe in the feed guide to the router through the feed web assistant, and then swipe in the third-party firmware through the feed guide. Breedboot is equivalent to the BIOS of the computer. As long as you swipe breedboot into the router, you can swipe in the third-party firmware at will. Before the operation, you need to download the third-party firmware (the third-party firmware is: & 160; Padavan, tomato Phoenix, Pandora box, openwrt). As for the breed web assistant, you can search by yourself. Let's start

2 / 2

connect the router to the computer through the network cable. If the router has been set before, please restore the router to the factory settings. After restoring the factory settings, open the browser and enter the default IP address of the router (here is 192.168.2.1), to see if you can log in to the router setting interface normally. If you can close the browser, proceed to the next step. Find the downloaded breed web assistant, right-click and select "run as administrator" (if there is a security software block, please add it as trust, in case of operation failure), and then select the brush scheme. You can choose according to the brand and model of your router (small editor is: K1, k1s, K2 automatic scheme), and other options remain the default. Then click the "start brushing" button and wait for the completion of brushing It's usually a one-time success. If something goes wrong in the middle, we have to start all over again. When the software prompts "brush complete", wait for two minutes to power off the router

swipe in the third party firmware

1 / 2

swipe in the firmware

1. Unplug the router, press and hold the router reset button, plug in the power, and wait about 10 seconds. 2. Open the browser and enter "192.168.1.1 & quot; Enter to enter the breed web console. 3. Click "restore factory settings" on the left side of the interface, select "config area (public version)" in the firmware type, and then click "execute" to wait for the execution to complete

view the remaining picture

2 / 2

and then click "firmware update" on the left side. Under normal firmware on the right side, check the firmware check box and click "select file" to add the prepared firmware. Next, click "Upload" to confirm the upload of firmware information, click "update" and wait for completion (do not disconnect the power supply of the router before it is finished, otherwise the router may become a brick)

view the remaining two pictures

router & # 160; The firmware

was edited on January 4, 2018, and the content is for reference only and protected by right

& 160; Like to share

read the full text

5. In this case, the router doesn't need to be flushed, just restore the factory settings. There is a switch at the back of the router. You can press it to restore the factory settings, or enter the advanced settings to restore the factory settings

6. Brushing firmware is software upgrade, which can repair defects, add new functions and increase stability
in addition to the hardware, many devices (optical drive, routing, motherboard, etc.) also have supporting "software" burned in ROM, and the operation of the device is driven by "software". Because these "software" are special underlying software, they are called "firmware"
upgrading firmware is not as new as possible. Generally, if there are no problems with the device and it can be used, do not upgrade it casually. Because: 1. New software may bring new problems; 2. May not match; 3. There are risks in brushing firmware, and failure of brushing may become a "brick".

7. Computer hardware problem. According to your description, rtl8197 chip router can not brush the third-party firmware. The reason is: Although the chip is the same, but other functions are different, third-party functions are also different, so can not brush.

8. DD wrt
tomato
but not all routers can use third-party firmware,
you need to go to the official websites of the above two firmware providers to find your router.