Bihu router blockchain service
as long as the app software is installed on the mobile phone, you can login and set it
the exclusive app interface is also very simple and clear, with three main moles: my routing, intelligent hardware and more
some basic settings of the router can be set, including modifying the password and Internet type of the router.
WAN port Internet access mode, which is generally PPPoE dial-up mode. In this way, you need to know the account password. After filling in the correct account password, you can access the Internet normally
if you are not using the Internet, but as an expansion device, you need to set up your route The gateway address of the router cannot be the same as that of the uplink device
I hope I can help you
Bihu router is a combination of high-speed and stable signal transmission, technology and strength, which adopts Qualcomm enterprise chip, built-in al antennas, gold-plated shielding wrapped sea blue RJ45 terminal, high-density anti-interference shielding multiplication layer. From the bird's nest to the family, from the enterprise to the indivial, the coverage area is up to 1949 square meters (under the condition of open space and no interference). It can support up to 100 terminals to surf the Internet without worry. Bihu routing depends on the demand, automatically allocates the bandwidth, adjusts the intensity, and effectively guarantees the concurrent use of multiple terminals with large traffic. Bihu routing app intelligent control, simple settings, security protection, intelligent speed limit, timing limit network, human management. Wpa-psk / wpa2-psk encryption, wireless access control, SSID hiding, dos and other network firewalls + app intelligent control make hackers have nowhere to pin
different Internet environment, wireless router setting method is different. If you need to dial a fiber-optic cat to connect to a wireless router, follow the following methods: 1. Plug in the wireless router, do not connect the cat, and connect the computer to any LAN port of the wireless router
; 2.
in the browser address bar, enter the IP address of the router (on the label on the back of the router), and enter the login user name and password to enter the settings page; 3. According to PPPoE (ADSL virtual dial-up) mode, input the internet account and password; 4. Set SSID, encryption method and
password; 5. Save and restart; 6. After setting, connect the cable from the cat LAN port to the WAN port of the wireless router
one, wired connection,
1, the network cable is inserted into the LAN port of the sub router to connect the computer, set the LAN port IP address to one of the IP addresses assigned to the main router, or set the LAN port IP address of the sub router wirelessly to one of the IP addresses assigned to the main router, turn off the DHCP service of the sub router, and finally connect the network cable to the LAN port of the main router
2. Insert the network cable into the WAN port of the router, connect the router, and set the router's Internet access mode to automatically obtain IP address or fixed IP address
Second, for wireless connection, the router has the function of bridging, and the sub router can directly bridge the main router.
if you need to dial a fiber-optic cat to connect to the wireless router, follow the following method:
1. Plug in the wireless router, do not connect the cat, and connect the computer to any LAN port of the wireless router
2. In the browser address bar, enter the IP address of the router (on the label on the back of the router), and enter the login user name and password to enter the settings page
3. Set according to PPPoE (ADSL virtual dial-up) mode, input internet account and password
4. Set SSID, encryption method and password
5. Save and restart
6. After setting, connect the cable from the cat LAN port to the WAN port of the wireless router.
It is recommended to turn off the router first. If there is still this WiFi signal and it can be connected, it proves that this WiFi signal is not sent by your router at all
if the router is al frequency, there are two signals with different frequencies, which can be configured in the router management interface
Chinanet vpcn this is the wireless in your Telecom Optical cat. Your optical cat should integrate the function of wireless router, because a TP-LINK router is connected behind your Telecom Optical cat, and your wireless router turns on the WiFi called rty, so you now have two WiFi.
first, if you have a wireless router, turn on the power first, Then plug in the Internet cable. The incoming cable is inserted into the WAN port, and then the network cable connected to the computer is inserted into any LAN port. After doing these jobs, you will see an address and account password behind the router. After connecting, enter the address you see in the router in the browser, which is 192.168.1.1, and enter the corresponding account and password, Generally, the newly bought ones are admin
to find the WAN port settings and enter the Internet access settings. We can see that there are three Internet access options. If your home is dial-up, then use PPPoE
when you choose PPPoE dial-up Internet access, you need to fill in your account number and password. You should understand that when you open broadband, you will have an account number to follow. Just fill in it and you will be OK
then the next step is wireless settings. We can see the channel, mode, security options, SSID and so on. Generally, SSID is a name, you can fill in it as you like, Then the mode mostly uses 11bgn. We need to choose WPA PSK for wireless security/