Hangzhou to Cixi passenger transport center
chamfering tool is also called chamfering tool. The chamfering cutter has a wide range of applications, which is not only suitable for chamfering ordinary machining parts, but also suitable for chamfering and deburring precision parts. Chamfering cutter is assembled on milling machine, drilling machine, planer, chamfering machine and other machine tools, which is used to process 60 degree or 90 degree chamfering of workpiece and inverted die edge angle of taper hole, belonging to end milling cutter< Advantages:
1) convenient clamping, without special clamping head, almost all rotary processing equipment and tools can be used, such as drilling machine, milling machine, lathe, machining center, electric tools, etc< It is not only suitable for chamfering of ordinary machining parts, but also suitable for chamfering and deburring of precision parts with difficult chamfering. Such as: aviation, military instry, automobile instry oil, gas, electric valve, engine cylinder, cylinder, ball through hole, inner wall hole
3) high working efficiency. Due to its own elastic strength, it can realize rapid processing operation, and can obtain good processing effect regardless of manual free operation or automatic timing feeding
4) it can be grinded repeatedly, suitable for mass proction, and can effectively rece the cost
5) this proct should be used before tapping; After tapping, the thread may be damaged.
G02 ------ clockwise circular interpolation
G03 ------ counterclockwise circular interpolation
example: G02 X60 Z50 i40 K0 F120
format 2: G02 x (U)____ Z(w)____ R+－__ F__
Description:
(1) can not be used for the programming of the whole circle
(2) r is the radius of the unilateral r arc of the workpiece. R is signed, and "+" means that the arc angle is less than 180 degrees; "-" Indicates that the arc angle is greater than 180 degrees. Where "+" can be omitted
(3) when the length between the end point and the starting point is greater than 2R, the arc is replaced by a straight line 
example: G02 X60 Z50 R20 F120
format 3: G02 x (U)____ Z(w)____ CR=__ Radius) f__
format 4: G02 x (U)____ Z(w)__ D__ Diameter) f___
these two programming formats are basically the same as format 2
interpolation along circle
note: except that the direction of arc rotation is opposite, the format is the same as G02 instruction
G04 - timed pause
format: G04__ F__ Or G04__ K__
Description: the processing motion was suspended, and the processing was continued after the time. The pause time is specified by the data after F. The unit is seconds
Therange was 0.01 seconds to 300 seconds
extended data
g331 - thread processing cycle
format: g331 x__ Z__ I__ K__ R__ p__
Description:
(1) diameter change in X direction, x = 0 is straight thread
(2) Z is thread length, absolute or relative programming can be used
(3) I is tail length in X direction after thread cutting, ± Value
(4) diameter difference between outer diameter and root diameter of R thread, positive value
(5) k pitch KMM
(6) number of processing cycles of P thread, i.e.
after cutting by several tools ÷ P and rounding, the last knife does not feed to finish the thread surface
2, internal thread tail according to the positive and negative direction of X determine the I value
The starting position of thread processing cycle is to align the tool tip with the outer circle of thread1) It is convenient for clamping, without special chuck, almost all rotary processing equipment and tools can be used, such as drilling machine, milling machine, lathe, machining center, electric tools, etc
2) it has a wide range of applications, not only suitable for chamfering of ordinary machining parts, but also suitable for chamfering and deburring of precision parts difficult to chamfering. Such as: aviation, military instry, automobile instry oil, gas, electric valve, engine cylinder, cylinder, ball through hole, inner wall hole
3) high working efficiency, because of its own elastic strength, it can achieve rapid processing operation, whether manual free operation or automatic timing feed can obtain good processing effect
4) it can be grinded repeatedly, suitable for mass proction, and can effectively rece the cost
5) this proct should be used before tapping; After tapping, the thread may be damaged
Machining center processing 30 ° The chamfering is 60 ° The problem of chamfering cutter, which depends on the specific situation, needs to judge whether there is enough space for 60 ° There is no other interference in the tool path ring the chamfering process
In my opinion, whether interest is paid or not, banks will perform the function of convertibility of digital currency. There are two reasons. First, from a macro point of view, digital RMB emerges as the times require. This kind of RMB can not only alleviate our current situation & mdash& mdash; In reality, the use of RMB is less, and it can strengthen the circulation of RMB and facilitate the management of RMB{ RRR} 2. The issue of digital RMB does not need to be bound by specific banks. The advantage of digital RMB is that it is free from the trouble of binding banks. Therefore, I dare to guess that digital RMB may be an independent currency, which does not need to be bound and stored by specific banks, but circulates as cash, Most banks will treat digital RMB in the same way as real RMB, so there is no conflict of exchange function