Jijia Z170 improves computing power
Publish: 2021-05-12 08:16:12
1. You can try the following methods:
1) remove the CMOS battery after power off and leave it for a period of time to clear the BIOS settings
2) after removing the hard disk, boot it into BIOS.
1) remove the CMOS battery after power off and leave it for a period of time to clear the BIOS settings
2) after removing the hard disk, boot it into BIOS.
2. Are you talking about processor frequency or graphics card? The processor frequency depends on what processor you match. As long as the interface is lga1151, this motherboard can support it at present
in terms of memory, this motherboard can support DDR4 3866mhz memory mole at most<
the description of the official website is as follows:
support DDR4 3866 (O.C) / 3733 (O.C) / 3666 (O.C) / 3600 (O.C.) / 3466 (O.C.) / 3400 (O.C.) / 3333 (O.C.) / 3300 (O.C.) / 3200 (O.C.) / 3000 (O.C.) / 2800 (O.C.) / 2666 (O.C.) / 2400 (O.C.) / 2133 MHz, 4 DDR4 DIMM slots, up to 64 GB memory
if you don't understand, please ask and adopt it in time after the problem is solved, thank you.
in terms of memory, this motherboard can support DDR4 3866mhz memory mole at most<
the description of the official website is as follows:
support DDR4 3866 (O.C) / 3733 (O.C) / 3666 (O.C) / 3600 (O.C.) / 3466 (O.C.) / 3400 (O.C.) / 3333 (O.C.) / 3300 (O.C.) / 3200 (O.C.) / 3000 (O.C.) / 2800 (O.C.) / 2666 (O.C.) / 2400 (O.C.) / 2133 MHz, 4 DDR4 DIMM slots, up to 64 GB memory
if you don't understand, please ask and adopt it in time after the problem is solved, thank you.
3. Gigabyte ga-z170x-gaming
7 is the first flagship of Gigabyte Z170. It is very similar to z170x-gaming
G1. This motherboard can be overclocking.
7 is the first flagship of Gigabyte Z170. It is very similar to z170x-gaming
G1. This motherboard can be overclocking.
4. Gigabyte Z170's motherboard has many models, but even the lowest end can support 2133 to 3200 (OC), so the frequency of 2400 is no problem. Pirate ship's memory has always been known for its high-end, compatibility and stability are its brand value, which is already very good. It's not very overclocking. Avengers are absolutely stable. Overclocking is recommended to be a platinum ruler. It's a little more expensive
pure hand fighting, hope to adopt~
pure hand fighting, hope to adopt~
5. Generally, the AHCI format needs to be set from the BIOS to replace the SSD<
setting mode:
1) the main board is the hard disk mode of Phoenix BIOS setting. Method: Press & quot when starting up; Del" Key to enter BIOS, use the right arrow key to select "advanced" item, enter this menu, find "SATA controller mode" option, switch to this item through the down arrow key, press "enter" key to pop up a dialog box, you can change the hard disk mode, such as setting to & quot; AHCI"， Select through the direction key, and then enter. When finished, press F10 to save and exit BIOS
2) the motherboard is the hard disk setting mode of the award BIOS; Del" Enter the BIOS and find & quot; Integrated Peripherals"( Integrate peripheral devices), select this item with the direction key, enter, open this item, and find "onchip SATA Controller & quot; And set it to "enabled & quot;, Then find "onchip SATA type & quot; There are three options "native ide & # 92; RAID\ AHCI" Select "AHCI" and change the value through "page up" / & quot; Page Down" After modification, press & quot; F10" Save to exit BIOS Note: some motherboards set the hard disk mode item as "SATA mode", and the method of changing the value is the same)
the following is the most popular installation method of installing the system through USB flash disk:
first, download the operating system. You can download the system according to the website address given below, which is safe, convenient and rich in resources
there are also detailed computer system installation tutorials in win7 flagship base This is very important)
make a system startup installation disk with USB flash disk
(you need to use the "computer store super USB flash disk proction tool v6.1 (UEFI startup experience)" to install: (it is also applicable to the installation of a separate system)
specific method:
prepare a USB flash disk equal to or greater than 4GB, and complete the formatting first
A. from the official website of u.diannaodian.com (http: / /) - download the "super U-disk startup tool v6.1 (UEFI startup experience)"
B. before running the program, please close the antivirus software and security software as much as possible (this software involves the read-write operation of removable disk, and some false positives of killing software may lead to proction failure!) After downloading, double-click to run under Windows XP system. For Windows Vista or windows 7 / 8 system, right-click to run as administrator< 1. Default mode:
1.1: open the main program, insert the USB disk / SD card and other removable devices, and the disk list will automatically list the letter, model, capacity and other information of all removable disks in the current computer
default mode 1.2: select the removable disk that you want to make boot. The boot mode is usb-hdd or usb-zip, and the default mode is usb-hdd CHS mode is mainly for some undetectable BIOS. Generally, you don't need to check this! If you want to convert the rest of the U disk to NTFS format, you can check the NTFS option. Note: formatting to NTFS will affect the use of the startup functions of the U disk. Unless you need to store a single file over 4G, it is not recommended to check this option!)
default mode 1.3: try to quit antivirus software and security software, so as to avoid failure in proction. Click the "one button proction start U disk" button, and the program will prompt whether to continue, After confirming that the selected USB flash disk has no important data, click start making.
(Note: use the USB flash disk making tool 2.0 in the computer store and the USB flash disk made in previous versions. If the making fails, please initialize the USB flash disk first)
Default mode 1.4: the making process is different according to the computer configuration and USB flash disk chip, so please wait patiently. After the completion of the proction, the correct setting of the computer BIOS can be started from the U disk. In order to verify the success of USB flash disk startup, you can run simulation startup
note: the simulated startup is only used to test whether the USB flash disk is successfully started, not to test the internal dos and PE system<
2. ISO mode:
ISO mode 2.1: switch to ISO mode or directly click ISO proction in the upper left corner of the main program, and the program will switch to the ISO proction interface<
ISO mode 2.2: after clicking the "one click to start USB flash disk" button, the program will be displayed in "D: &# 92; Computer shop ISO & "92;" Create a dnd.iso image under the folder
ISO mode 2.3: open the USB flash drive in ISO mode, click the button in ISO mode, select according to the recommended options in the figure, and finally click the write button to wait for the completion of writing If you need to burn a disc, click the "burn disc" button to burn it!)
note: ISO mode also supports writing win7 or win8 system image to U disk as system installation disk
make the system installation disk of USB flash disk according to the above steps, and then you can install win7 or win8 system
note:
how to set the USB flash disk as the first boot order device 1:
turn on the computer. According to the first boot screen that has just flashed, the white prompt text at the bottom of the screen generally appears "del", then press the "del (delete)" key; If it is something else, you can try pressing F2, F8, F10, F12 and so on according to the prompt to enter the BIOS. Because different models of computers have different BIOS settings according to different motherboards. First, you can find the big item with the word "boot" in the menu, then go to the detail item and select the first boot: this means the first boot driver for the computer to start. Select here (use the up and down arrows, Or there is a "USB" device at the bottom of the screen, and then press F10 to save it and restart it. When the computer restarts and there is a USB boot disk that can be supported, the system installation interface for entering the USB disk will be displayed on the screen
method 2 of setting USB flash drive as the first boot device:
turn on the computer. According to the prompt displayed at the bottom of the computer in the first boot screen, F9 (or F2 or F12) can be continuously used to enter the quick boot device selection menu. Select the device with the word "USB" in the menu, or enter the boot mode of USB flash drive The steps are the same as method 1)
the process of installing the system through the USB flash disk is basically fool like, and you can follow the prompts of the system installation interface step by step, which is very simple and will not be described here.)
if you have any questions, please ask and reply
if you are satisfied, please give me a ~ ~, thank you!
setting mode:
1) the main board is the hard disk mode of Phoenix BIOS setting. Method: Press & quot when starting up; Del" Key to enter BIOS, use the right arrow key to select "advanced" item, enter this menu, find "SATA controller mode" option, switch to this item through the down arrow key, press "enter" key to pop up a dialog box, you can change the hard disk mode, such as setting to & quot; AHCI"， Select through the direction key, and then enter. When finished, press F10 to save and exit BIOS
2) the motherboard is the hard disk setting mode of the award BIOS; Del" Enter the BIOS and find & quot; Integrated Peripherals"( Integrate peripheral devices), select this item with the direction key, enter, open this item, and find "onchip SATA Controller & quot; And set it to "enabled & quot;, Then find "onchip SATA type & quot; There are three options "native ide & # 92; RAID\ AHCI" Select "AHCI" and change the value through "page up" / & quot; Page Down" After modification, press & quot; F10" Save to exit BIOS Note: some motherboards set the hard disk mode item as "SATA mode", and the method of changing the value is the same)
the following is the most popular installation method of installing the system through USB flash disk:
first, download the operating system. You can download the system according to the website address given below, which is safe, convenient and rich in resources
there are also detailed computer system installation tutorials in win7 flagship base This is very important)
make a system startup installation disk with USB flash disk
(you need to use the "computer store super USB flash disk proction tool v6.1 (UEFI startup experience)" to install: (it is also applicable to the installation of a separate system)
specific method:
prepare a USB flash disk equal to or greater than 4GB, and complete the formatting first
A. from the official website of u.diannaodian.com (http: / /) - download the "super U-disk startup tool v6.1 (UEFI startup experience)"
B. before running the program, please close the antivirus software and security software as much as possible (this software involves the read-write operation of removable disk, and some false positives of killing software may lead to proction failure!) After downloading, double-click to run under Windows XP system. For Windows Vista or windows 7 / 8 system, right-click to run as administrator< 1. Default mode:
1.1: open the main program, insert the USB disk / SD card and other removable devices, and the disk list will automatically list the letter, model, capacity and other information of all removable disks in the current computer
default mode 1.2: select the removable disk that you want to make boot. The boot mode is usb-hdd or usb-zip, and the default mode is usb-hdd CHS mode is mainly for some undetectable BIOS. Generally, you don't need to check this! If you want to convert the rest of the U disk to NTFS format, you can check the NTFS option. Note: formatting to NTFS will affect the use of the startup functions of the U disk. Unless you need to store a single file over 4G, it is not recommended to check this option!)
default mode 1.3: try to quit antivirus software and security software, so as to avoid failure in proction. Click the "one button proction start U disk" button, and the program will prompt whether to continue, After confirming that the selected USB flash disk has no important data, click start making.
(Note: use the USB flash disk making tool 2.0 in the computer store and the USB flash disk made in previous versions. If the making fails, please initialize the USB flash disk first)
Default mode 1.4: the making process is different according to the computer configuration and USB flash disk chip, so please wait patiently. After the completion of the proction, the correct setting of the computer BIOS can be started from the U disk. In order to verify the success of USB flash disk startup, you can run simulation startup
note: the simulated startup is only used to test whether the USB flash disk is successfully started, not to test the internal dos and PE system<
2. ISO mode:
ISO mode 2.1: switch to ISO mode or directly click ISO proction in the upper left corner of the main program, and the program will switch to the ISO proction interface<
ISO mode 2.2: after clicking the "one click to start USB flash disk" button, the program will be displayed in "D: &# 92; Computer shop ISO & "92;" Create a dnd.iso image under the folder
ISO mode 2.3: open the USB flash drive in ISO mode, click the button in ISO mode, select according to the recommended options in the figure, and finally click the write button to wait for the completion of writing If you need to burn a disc, click the "burn disc" button to burn it!)
note: ISO mode also supports writing win7 or win8 system image to U disk as system installation disk
make the system installation disk of USB flash disk according to the above steps, and then you can install win7 or win8 system
note:
how to set the USB flash disk as the first boot order device 1:
turn on the computer. According to the first boot screen that has just flashed, the white prompt text at the bottom of the screen generally appears "del", then press the "del (delete)" key; If it is something else, you can try pressing F2, F8, F10, F12 and so on according to the prompt to enter the BIOS. Because different models of computers have different BIOS settings according to different motherboards. First, you can find the big item with the word "boot" in the menu, then go to the detail item and select the first boot: this means the first boot driver for the computer to start. Select here (use the up and down arrows, Or there is a "USB" device at the bottom of the screen, and then press F10 to save it and restart it. When the computer restarts and there is a USB boot disk that can be supported, the system installation interface for entering the USB disk will be displayed on the screen
method 2 of setting USB flash drive as the first boot device:
turn on the computer. According to the prompt displayed at the bottom of the computer in the first boot screen, F9 (or F2 or F12) can be continuously used to enter the quick boot device selection menu. Select the device with the word "USB" in the menu, or enter the boot mode of USB flash drive The steps are the same as method 1)
the process of installing the system through the USB flash disk is basically fool like, and you can follow the prompts of the system installation interface step by step, which is very simple and will not be described here.)
if you have any questions, please ask and reply
if you are satisfied, please give me a ~ ~, thank you!
6. Z170x
gaming3 gigabyte, first of all, you need your CPU with K in order to overclocking. Press and hold the Del key to enter the main board BIOS, find the CPU options, and set them in Chinese,
gaming3 gigabyte, first of all, you need your CPU with K in order to overclocking. Press and hold the Del key to enter the main board BIOS, find the CPU options, and set them in Chinese,
7. This is a completely normal phenomenon. Desktop computers do not have al graphics cards and cannot be integrated and used independently
connect the independent graphics card and connect the display to the independent graphics card to automatically shield the integrated display.
connect the independent graphics card and connect the display to the independent graphics card to automatically shield the integrated display.
8. No, i5 4570 is 1150 pin, Jijia z170-ud3 is 1151 pin, i5 4570 with b85.z97 is OK, Z170 with i5 6600k and i7 6700k
9. Download the BIOS file and put it on the hard disk or U disk (FAT32)
press the power on key, immediately press the end key to enter the BIOS built-in q-flash program, specify the storage location of the BIOS file, select the BIOS file to refresh
or press the power on key, immediately press the Del key, enter the main menu of the BIOS, and press the F8 key to call out q-flash.
press the power on key, immediately press the end key to enter the BIOS built-in q-flash program, specify the storage location of the BIOS file, select the BIOS file to refresh
or press the power on key, immediately press the Del key, enter the main menu of the BIOS, and press the F8 key to call out q-flash.
10. After inquiry, the parameters and prices of these models are very close, and they are very good on the whole. They are suitable to start with
but the key to buy things is whether the characteristics of the procts meet their own needs. Therefore, it is recommended to carefully weigh and choose the procts that are suitable for you in the future. Digital procts are paid for every cent and are more expensive in price, It's definitely better than the cheaper quality.
but the key to buy things is whether the characteristics of the procts meet their own needs. Therefore, it is recommended to carefully weigh and choose the procts that are suitable for you in the future. Digital procts are paid for every cent and are more expensive in price, It's definitely better than the cheaper quality.
Hot content