The 55th floor of Nanjing Center Building
Publish: 2021-04-18 20:06:46
1. 1. You'd better take it off when you wash your hands. You can't take a hot bath with your watch (even if it's a diving watch) because all watches are not steam proof. 2. The quartz watch should change the battery in time when there is no battery (no battery watch will prompt, generally the second hand will jump in 4 seconds). The mechanical watch should be maintained once every 2 to 3 years (go to the professional maintenance station to maintain the master). 3. Do not put the watch on the electrical appliance when the mechanical watch is not taken For example, microwave oven, refrigerator, stereo, automatic mahjong table and so on, because the watch is easy to be magnetized. If the watch is magnetized, you will find that the watch goes faster than usual, so that you can take it to the maintenance station to degausse for the master 4. Don't dial the calendar quickly from 9:00 p.m. to 3:00 a.m. for mechanical watch.
2.
In our daily life, when we wear a watch, if the watch mirror is broken, seriously damaged, such as burst, broken edges and corners, and debris is all over the dial, we need to take the following measures immediately. We must never dial the needle or quickly adjust the calendar, or try to remove the broken glass of the dial ourselves. Before the watch is sent to the clock repair shop for maintenance, the watch must be placed horizontally (preferably with the glass facing down) in the packing box. During the process of sending the watch for maintenance, there should be no violent vibration and shaking, which will cause greater failure. To find the after-sales service center, you can try the following aspects
< UL >to consult the official customer service below. This is a quick and easy way to find the glasuti repair center
go to wanlinghui watch repair shop in Tianhe District, Guangzhou. The repair shop is on the 7th floor of tower a. General formal watch repair shop can also carry out watch repair
3. Our address is: room 1102, 11th floor, block D, Huaxi International Center, Chaoyang International Trade, Beijing.
suggestions for the use of mechanical watch:
1. Watch with manual winding movement should be wound at the same time every day as far as possible, so that the watch can operate with enough energy in the next 24 hours
2. The energy of the watch with automatic winding movement comes from the movement of the wearer's arm, so it is not necessary to manually wind the watch under normal wearing conditions. Only when the wearer's movement is not enough to add enough energy to the spring, the watch can be manually wound up, and the crown rotation is controlled within 20 turns
3. For an automatic winding watch that has not been worn for more than 40 hours, turn the crown for 20 turns to start the drive system of the movement again
4. In order to prevent moisture from seeping into the watch case and keep the watch waterproof, please ensure that the crown is locked at all times
suggestions for the use of mechanical watch:
1. Watch with manual winding movement should be wound at the same time every day as far as possible, so that the watch can operate with enough energy in the next 24 hours
2. The energy of the watch with automatic winding movement comes from the movement of the wearer's arm, so it is not necessary to manually wind the watch under normal wearing conditions. Only when the wearer's movement is not enough to add enough energy to the spring, the watch can be manually wound up, and the crown rotation is controlled within 20 turns
3. For an automatic winding watch that has not been worn for more than 40 hours, turn the crown for 20 turns to start the drive system of the movement again
4. In order to prevent moisture from seeping into the watch case and keep the watch waterproof, please ensure that the crown is locked at all times
4. For mechanical watch, movement oil washing is the key to its service life. How often is the mechanical watch maintained? It seems to be a simple question, but it is difficult to make it clear. In fact, there is no strict standard for this. Watches are like cars. When it's time to recommend maintenance, they don't go. It won't be a problem to drive for a few more months. As a rule, cleaning once every 3-5 years is good for prolonging the service life of the meter
watch wearing: if you often wear or wear a watch every day, under frequent use, the wear degree of the parts is relatively large, and the wear degree is relatively high, so it is best to maintain them regularly. On the contrary, if it is not used for a long time, the wear degree of the parts will be small, but the oil will become thicker and thicker with the passage of time. In this case, it is OK to extend the cycle, but maintenance is needed before wearing it again. Large temperature difference will also shorten the watch maintenance cycle
watch sealing problem: the oil in the watch is easy to deteriorate and volatilize e to poor conditions. It is very sensitive to moisture, st, fiber and other foreign matters. The movement is easy to rust. If there are small impurities between the gear and the parts, the damage to the movement will increase
if the watch slows down and the top wind is still like this, maintenance should be considered. There are always some symptoms when you really need maintenance. This is the watch reminding you: if you don't repair it, I'll be finished. Severe wear of parts may occur. There is no need to be slow to send to the maintenance, so there is a certain damage to the watch, wear increases, affect life
how to prolong the life and maintenance cycle of watch: Three Preventions and one guarantee! The so-called three proofs are: antimagnetic, waterproof and shockproof. One supplement is: let the watch have enough power. Corresponding to watch maintenance three fears: fear of magnetism, fear of moisture, fear of falling!
watch wearing: if you often wear or wear a watch every day, under frequent use, the wear degree of the parts is relatively large, and the wear degree is relatively high, so it is best to maintain them regularly. On the contrary, if it is not used for a long time, the wear degree of the parts will be small, but the oil will become thicker and thicker with the passage of time. In this case, it is OK to extend the cycle, but maintenance is needed before wearing it again. Large temperature difference will also shorten the watch maintenance cycle
watch sealing problem: the oil in the watch is easy to deteriorate and volatilize e to poor conditions. It is very sensitive to moisture, st, fiber and other foreign matters. The movement is easy to rust. If there are small impurities between the gear and the parts, the damage to the movement will increase
if the watch slows down and the top wind is still like this, maintenance should be considered. There are always some symptoms when you really need maintenance. This is the watch reminding you: if you don't repair it, I'll be finished. Severe wear of parts may occur. There is no need to be slow to send to the maintenance, so there is a certain damage to the watch, wear increases, affect life
how to prolong the life and maintenance cycle of watch: Three Preventions and one guarantee! The so-called three proofs are: antimagnetic, waterproof and shockproof. One supplement is: let the watch have enough power. Corresponding to watch maintenance three fears: fear of magnetism, fear of moisture, fear of falling!
5. The reasons and solutions of watch's inaccurate travel time:
1. Insufficient power storage. It is necessary to check whether the power is sufficient first. If the amount of movement of the mechanical watch with automatic chaining is very small, it may also cause insufficient power storage. You can supplement the power by manual chaining, and then observe whether there is a continuous phenomenon of speed. If it is still recommended to go to a special repair shop for inspection
2. If the quartz watch suddenly finds that it is slow, it may be caused by insufficient battery energy. Send the watch to a special maintenance point to check the power or replace the battery
3. The watch is very tight. If it is hit or hit, the internal parts may be loose and damaged. It may also cause travel time problems. It is recommended to go to a special repair shop for inspection
4. Maintenance required. Movement oil shortage or internal parts wear and aging may cause travel time problems, need maintenance, need to be sent to the designated repair point for maintenance service
5. Under the influence of ambient temperature, the watch is magnetized: if the hairspring of the watch is magnetized, the watch's travel time will be inaccurate. The influence of the wearer's use habits may cause the increase of travel time error. Send the watch to the designated maintenance point for professional inspection and adjustment, which can restore the watch to the normal error range
note:
1. The mechanical watch varies according to the model and manufacturing quality of the movement. Generally, the error of a famous watch within 30 seconds per day is within the normal range. Some movements with higher accuracy can reach about 10 seconds< Generally speaking, the accuracy of quartz watch is high, and the Swiss standard is that the monthly error is within 15 seconds. Some precise movements can achieve annual error within a few seconds.
1. Insufficient power storage. It is necessary to check whether the power is sufficient first. If the amount of movement of the mechanical watch with automatic chaining is very small, it may also cause insufficient power storage. You can supplement the power by manual chaining, and then observe whether there is a continuous phenomenon of speed. If it is still recommended to go to a special repair shop for inspection
2. If the quartz watch suddenly finds that it is slow, it may be caused by insufficient battery energy. Send the watch to a special maintenance point to check the power or replace the battery
3. The watch is very tight. If it is hit or hit, the internal parts may be loose and damaged. It may also cause travel time problems. It is recommended to go to a special repair shop for inspection
4. Maintenance required. Movement oil shortage or internal parts wear and aging may cause travel time problems, need maintenance, need to be sent to the designated repair point for maintenance service
5. Under the influence of ambient temperature, the watch is magnetized: if the hairspring of the watch is magnetized, the watch's travel time will be inaccurate. The influence of the wearer's use habits may cause the increase of travel time error. Send the watch to the designated maintenance point for professional inspection and adjustment, which can restore the watch to the normal error range
note:
1. The mechanical watch varies according to the model and manufacturing quality of the movement. Generally, the error of a famous watch within 30 seconds per day is within the normal range. Some movements with higher accuracy can reach about 10 seconds< Generally speaking, the accuracy of quartz watch is high, and the Swiss standard is that the monthly error is within 15 seconds. Some precise movements can achieve annual error within a few seconds.
6. There is no special after-sales service center in Nanjing for the time being. If your watch has not passed the warranty period, it is recommended that you get it to our after-sales service center. When you buy your watch, the warranty card comes with the address and telephone number; If the warranty period, you can also choose some large professional regular repair shop
you can get Guangcheng watch shop, room 2109, 21 / F, Suning Plaza North Tower, 109 Renmin Middle Road, Wuxi City, and ask the master to help you with the inspection and maintenance<
reasons for the mechanical watch to stop stealthily:
watch stop: people who know a little about the mechanical watch know that the automatic mechanical watch is completely dependent on the swing of the arm to complete the winding. Therefore, once the watch is placed for a long time or the daily arm activity does not meet the requirements of the watch winding, the watch will lead to the lack of potential energy e to winding, which will cause the watch to go unstable or stop at night when it is not worn. If this happens, we can do arc motion manually before the watch is placed. Or use the manual winding function to wind the watch. In this way, the watch has enough kinetic energy to keep it running until the next day
watch knock: because the watch is exposed most of the time ring wearing, it is easy to knock other hard objects when walking., If you accidentally knock or fall on the watch in daily use, it may lead to the movement gear and other parts of the watch loose, dislocation and other situations, which will also lead to the mechanical watch to stop stealthily
hairspring problem: hairspring fault is also one of the reasons for the mechanical watch to stop stealthily when it is running normally. As we said earlier, some people stop their watches secretly e to insufficient activity. If the activity is too large, the winding mechanism will be broken down e to the tightening of the winding for a long time. It can also cause a lack of motivation. Generally, this kind of stop will happen from 9:00 to 12:00 in the evening. At this time, the watch with calendar function will drive the calendar wheel. It directly led to the lack of power, the calendar jammed and stopped
in addition, some other situations, such as the watch is magnetized, too much grease and so on, can also cause the mechanical watch to stop.
you can get Guangcheng watch shop, room 2109, 21 / F, Suning Plaza North Tower, 109 Renmin Middle Road, Wuxi City, and ask the master to help you with the inspection and maintenance<
reasons for the mechanical watch to stop stealthily:
watch stop: people who know a little about the mechanical watch know that the automatic mechanical watch is completely dependent on the swing of the arm to complete the winding. Therefore, once the watch is placed for a long time or the daily arm activity does not meet the requirements of the watch winding, the watch will lead to the lack of potential energy e to winding, which will cause the watch to go unstable or stop at night when it is not worn. If this happens, we can do arc motion manually before the watch is placed. Or use the manual winding function to wind the watch. In this way, the watch has enough kinetic energy to keep it running until the next day
watch knock: because the watch is exposed most of the time ring wearing, it is easy to knock other hard objects when walking., If you accidentally knock or fall on the watch in daily use, it may lead to the movement gear and other parts of the watch loose, dislocation and other situations, which will also lead to the mechanical watch to stop stealthily
hairspring problem: hairspring fault is also one of the reasons for the mechanical watch to stop stealthily when it is running normally. As we said earlier, some people stop their watches secretly e to insufficient activity. If the activity is too large, the winding mechanism will be broken down e to the tightening of the winding for a long time. It can also cause a lack of motivation. Generally, this kind of stop will happen from 9:00 to 12:00 in the evening. At this time, the watch with calendar function will drive the calendar wheel. It directly led to the lack of power, the calendar jammed and stopped
in addition, some other situations, such as the watch is magnetized, too much grease and so on, can also cause the mechanical watch to stop.
7. Address: room 01, 20 / F, Yingli international financial center, No. 28, Minquan Road, Yuzhong District, Jiefangbei, Chongqing,
if you just bought a new watch, you can go to the after-sales service to replace it if you don't wear the strap. Generally speaking, the warranty period of a watch is 2 years. Although the belt is not covered by the warranty in many cases, you can also go to the after-sales department for those who have just bought it
if the strap of a watch worn for a long time is broken, it can be taken to a special repair point for repair according to the specific situation, which is also more convenient
for watches of different brands, styles and prices, the strap is also different. There are leather, steel and chain. The breakage of the strap depends on the situation. If it's really serious and there's no way to repair it, you can only replace it with a new one
If a watch is a kind of decorative strap, usually a chain, then if one section is broken, it can be removed completely, and then it can be fastened again, which is similar to many people's bracelets
because the watch is worn on the neck of the hand, it's very convenient to watch. Once you find that you want to disconnect it, you need to find a way to solve it. It's not as good as leather. If you split a little, you can stick it with glue, so it won't be so easy to break it all
as the maintenance requirements of each watch strap are different, you need to choose a watch according to your own needs. For example, the leather strap is very high-end, and can show a unique personal temperament, but it is not suitable for summer wear, because the sweat in the body is corrosive to the strap, and also needs to do the corresponding maintenance.
if you just bought a new watch, you can go to the after-sales service to replace it if you don't wear the strap. Generally speaking, the warranty period of a watch is 2 years. Although the belt is not covered by the warranty in many cases, you can also go to the after-sales department for those who have just bought it
if the strap of a watch worn for a long time is broken, it can be taken to a special repair point for repair according to the specific situation, which is also more convenient
for watches of different brands, styles and prices, the strap is also different. There are leather, steel and chain. The breakage of the strap depends on the situation. If it's really serious and there's no way to repair it, you can only replace it with a new one
If a watch is a kind of decorative strap, usually a chain, then if one section is broken, it can be removed completely, and then it can be fastened again, which is similar to many people's bracelets
because the watch is worn on the neck of the hand, it's very convenient to watch. Once you find that you want to disconnect it, you need to find a way to solve it. It's not as good as leather. If you split a little, you can stick it with glue, so it won't be so easy to break it all
as the maintenance requirements of each watch strap are different, you need to choose a watch according to your own needs. For example, the leather strap is very high-end, and can show a unique personal temperament, but it is not suitable for summer wear, because the sweat in the body is corrosive to the strap, and also needs to do the corresponding maintenance.
8. If the water is not serious, there is only a layer of fog in the watch glass. At this time, wrap the watch tightly with several layers of toilet paper or absorbent flannelette, and bake it at 15cm away from the 40W light bulb for about 30 minutes to eliminate the water vapor. Do not bake the cover close to the fire, so as not to deform the cover. It can also be worn on the wrist with the watch cover facing inside and the bottom shell facing out, and the moisture can be eliminated after two hours
of course, there are some daily repair methods for watch water:
1. If there is water in the watch case, a kind of granular material called silica gel can be put into a closed container together with the watch that has accumulated water. After a few hours, take out the watch and the water will disappear. This method is simple and economical, without any damage to the accuracy and life of the meter. The silica gel that has absorbed water for many times can be dried at 120 ℃ for several hours. The water absorption capacity is renewable and can be used repeatedly
2. If the water is not serious, but there is a layer of fog in the glass, then use several layers of toilet paper or easy to absorb moisture flannelette to wrap the watch tightly, and bake it at 15cm away from the 40W light bulb for about 30 minutes to eliminate the water vapor. Do not bake the cover close to the fire, so as not to deform the cover
3. It can also be worn on the wrist with the watch cover facing inside and the bottom shell facing out, and the moisture can be eliminated after two hours. If the water is serious
4. None of the above three methods can remove the water vapor, so it should be sent to the meter shop to wipe oil immediately to remove the moisture of the movement, so as to avoid parts rusting
5. If the water is not serious, but there is a layer of fog in the glass, then use several layers of toilet paper or easy to absorb moisture flannelette to wrap the watch tightly, and bake it at 15cm away from the 40W light bulb for about 30 minutes to eliminate the water vapor. Do not bake the cover close to the fire, so as not to deform the cover
6. Dry the glass with a hair dryer, keep the temperature not too high, keep the wind gentle, and know that you can't see the moisture on the glass
if the water is serious, it is better to send it to the meter shop immediately to wipe oil to remove the moisture of the movement, so as to avoid parts rusting. Remember not to remove it by yourself, so as to avoid damage to the movement. It will take more time and money to repair.
of course, there are some daily repair methods for watch water:
1. If there is water in the watch case, a kind of granular material called silica gel can be put into a closed container together with the watch that has accumulated water. After a few hours, take out the watch and the water will disappear. This method is simple and economical, without any damage to the accuracy and life of the meter. The silica gel that has absorbed water for many times can be dried at 120 ℃ for several hours. The water absorption capacity is renewable and can be used repeatedly
2. If the water is not serious, but there is a layer of fog in the glass, then use several layers of toilet paper or easy to absorb moisture flannelette to wrap the watch tightly, and bake it at 15cm away from the 40W light bulb for about 30 minutes to eliminate the water vapor. Do not bake the cover close to the fire, so as not to deform the cover
3. It can also be worn on the wrist with the watch cover facing inside and the bottom shell facing out, and the moisture can be eliminated after two hours. If the water is serious
4. None of the above three methods can remove the water vapor, so it should be sent to the meter shop to wipe oil immediately to remove the moisture of the movement, so as to avoid parts rusting
5. If the water is not serious, but there is a layer of fog in the glass, then use several layers of toilet paper or easy to absorb moisture flannelette to wrap the watch tightly, and bake it at 15cm away from the 40W light bulb for about 30 minutes to eliminate the water vapor. Do not bake the cover close to the fire, so as not to deform the cover
6. Dry the glass with a hair dryer, keep the temperature not too high, keep the wind gentle, and know that you can't see the moisture on the glass
if the water is serious, it is better to send it to the meter shop immediately to wipe oil to remove the moisture of the movement, so as to avoid parts rusting. Remember not to remove it by yourself, so as to avoid damage to the movement. It will take more time and money to repair.
9. 1. It's best not to throw your glaxotti watch directly into the dresser or drawer. It is suggested to take off the glasuti watch, wrap it with soft cloth and lay it flat. The more careful the maintenance of the watch mirror, the less it will be scratched. If the mirror is damaged or scratched, replace it immediately. Because even tiny cracks can make st or moisture erode the mechanical parts of the meter, threatening the accuracy of the meter
2. Every two years, you will find that your watch may run slowly or fast, or even no longer work. All you need to do is send the watch to a professional watch Maintenance Center for repair
3. Conct waterproof test and appearance cleaning for the watch once a year; Quartz movement watch, every 5 ~ 7 years to do a whole machine maintenance; Mechanical movement watch, every 3 ~ 5 years to do a whole machine maintenance.
2. Every two years, you will find that your watch may run slowly or fast, or even no longer work. All you need to do is send the watch to a professional watch Maintenance Center for repair
3. Conct waterproof test and appearance cleaning for the watch once a year; Quartz movement watch, every 5 ~ 7 years to do a whole machine maintenance; Mechanical movement watch, every 3 ~ 5 years to do a whole machine maintenance.
Hot content