5700 superfrequency computing power

1. 1. Press & quot; after power on or restart del" The left side of enter in the keyboard area, or & quot; delete", It's a hit, not a hold)

2; Basic Input&Output System" The full name of, hehe, we should understand it

3. Find the & quot on the right (usually the right column); Frequency/Voltage Control"， Click & quot; enter" To enter

4. General overclocking, small overclocking, only need this change & quot; CPU Frequency"， In the case of external frequency 200MHz (depending on the actual situation, there are 133MHz, etc.) and the default frequency doubling. If you want the main frequency of 3200mhz and the frequency multiplication is 15, then use the main frequency / frequency multiplication = 213 and change it to 213mhz (manual input). If you don't mind, you can try 215 / 220 one by one. If it is a small super, go to Article 7 directly

5. If you need to greatly overclock, for example, the default main frequency is 3000MHz and the frequency doubling is 15. If you want to overclock to 3800mhz, the external frequency should be 253mhz. However, when you modify it, you find that it can't power on or the default value in the BIOS after power on. At this time, you need to add CPU voltage, which is to give it more energy to run further, If the voltage is applied, the heat proction will start to increase by a large margin. Try to use it

6. If the CPU voltage is applied, if it still fails, you need to rece the frequency of the memory (see the reasons below, Annex 3). In the BIOS, select the advanced chipset features - memclock value on the left. In the memory clock, there are three choices: Auto / limit / manual, we choose & quot; Manual", Then rece the frequency appropriately according to the actual situation, and then increase the CPU frequency. If it still can't, you may need to pressurize the memory, that is, DIMM / chip voltage option In case of overclocking, if it is AMD CPU, it is recommended to turn off amd K8 Q & C temporarily

7. When you are ready, don't forget to increase the fan speed. In BIOS - PC health status cpufan mode setting, select manual mode and change it to 255 (0-255 level, the higher the speed is)

8. Press F10, select Yes / OK, restart the system automatically, and enter the system after automatic adjustment and stabilization. Otherwise, it will enter the BIOS. In serious cases, it may fail to start the system (the countermeasures are discussed below, annex 2)

9. Determine the stability and download & quot; As long as the software can run stably for more than 3 hours and the temperature is below 70 ℃, the overclocking is successful

see:
for details http://hi..com/an0011121/blog/item/4143df88ee8f449aa4c272a1.html

2. Of course, the higher the CPU, the better. However, the CPU quality and heat dissipation conditions decide that it can exceed the stable or the highest value. It is not recommended to exceed too high, because the CPU is a low-end processor, so the performance improvement is not significant.

3. For novices, go to the next overdrive
of course, brand computers and laptops can't surpass

4. It's very good that 5700 standard can exceed that high
My 5800 standard can only exceed 550 / 900, which seems to be DDR2's video memory (I can't see the heat sink, the default is 400 / 800)
because of the calorific value, I don't dare to exceed it much
you can check the temperature and run the test software. If the temperature is within the acceptable range, then it can be used. No problem

5. This kind of overclocking degree is not high, as long as do a good job of heat dissipation, it does not affect the CPU life, can be used at ease

6. < UL >

after power on or restart, press & quot del"

enter the BIOS with blue screen and white characters (& quot; Basic Input& Output System" (the full name of)

find the & quot; Frequency/Voltage Control"， Click & quot; enter" get into; General overclocking, small ultra, just the change & quot; CPU Frequency"， External frequency 200MHz and default frequency doubling. If you want the main frequency of 3200mhz and the frequency multiplication is 15, then use the main frequency / frequency multiplication = 213 and change it to 213mhz. If you are not at ease, you can try 215 / 220... One by one. If you are a small super, you can go to Article 7 directly

if you need to greatly overclock, for example, the default main frequency is 3000MHz, and the frequency multiplier is 15. If you want to overclock to 3800mhz, the external frequency should be 253mhz, but when you modify it, you find that you can't boot or the default value in the BIOS after boot. At this time, you need to add CPU voltage, which is to give it more energy to run further

if the CPU voltage is applied, if it still fails, it is necessary to rece the frequency of the memory. In BIOS, select advanced chipset features - memclock value on the left. In memory clock, there are three choices: Auto / limit / manual, we choose & quot; Manual", Then rece the frequency according to the actual situation, and then increase the CPU frequency. If it still can't, you may need to pressurize the memory, that is DIMM / chip voltage option

when you are ready, don't forget to increase the fan speed. In BIOS - PC health status cpufan mode setting, select manual mode and change it to 255
Press F10, select Yes / OK, restart automatically, and enter the system after automatic adjustment and stabilization. Otherwise, it will enter the BIOS, or it may fail to boot in serious cases

determine stability, Download & quot; As long as the software can run stably for more than 3 hours and the temperature is below 70 ℃, the overclocking is successful

7. P43 motherboard... There are many models with different designs. It depends on the specific electrical performance. It mainly depends on the power supply of CPU
generally, the CPU of Intel can exceed 50% Other conditions can keep up)
the e5000 series may be on a wafer
just like the e5700e5800, the constitution is better
so the default dominant frequency is higher
the positive impurities on a wafer and near the center of the circle are less
like your E5700. The default is 3.0. The physique is better. The air cooling limit should be 4.5g
I have seen the evaluation of E5200. It can exceed 3.9ghz.
there is also a big relationship with memory
of course, it depends on your technology
of course, it depends on your overclocking technology
fever. Intel's al core, generally not big. Don't be careful
PS: overclocking brings little performance improvement.

8. Why do I see that your cpuz diagram is e8400, not E5700
overclocking must be harmful, but it depends on the degree of influence and the temperature. U generally has 10 years of life, you also have 5 years of life, 5 years later your CPU do not know which mp. Plus you're only 3.7g, that's super. E8400 is 3G by default, because what you show me is e8400 diagram, so I can only comment with it. It's just that the voltage is not high. Long term use is no problem! Over to the frequency you want, you can use the toaster software to measure the full load, to see whether the cooling temperature is OK, and whether the blue screen will be! It's stable after that
I introce you a toaster, Linx very strong toaster software, baking CPU and memory, you do not know how to use, you can ask me, a good simple software, I believe you will use
it is not stable to pass the software, but it is not stable to pass the software test!

9. You this u not good overclocking, do not pressurize about 3.5, see your U constitution

10.

It is OK to exceed 15% - 20% on the premise that the motherboard supports it. The specific steps are as follows:

1. turn on the computer and enter the BIOS. In the CPU option, there is usually a position that supports external frequency exceeding, which is a group of numbers. For example, if the CPU defaults to 200MHz, then 200 will be displayed at this position. You can choose this position to change the external frequency. If the external frequency is increased, the frequency of CPU will increase, and the purpose of overclocking is achieved

2. it should be noted that when the external frequency is exceeded, it should be exceeded bit by bit. For the first time, you can first adjust the external frequency to 205, and then restart the system to see if it is normal. If it is normal, you can come back and adjust it to 210. If it is normal, you can adjust the external frequency again and again. Until the system can not start normally when it is adjusted to a certain number, you can apply voltage to it, It should be added little by little, otherwise it may burn down. First of all, add 0.1V voltage, restart to see whether the normal restart, if not restart is overclocking limit

3. the heat dissipation of CPU is also very important. If the heat dissipation is not good, it will not only be too low, but also burn the CPU. So it must be equipped with a good fan, if necessary, water cooling can be used to dissipate heat

4. when the CPU exceeds the external frequency, the frequency of the memory will also follow. Therefore, in many cases, the overclocking is not successful

5. is often not the problem of CPU constitution, but the problem of memory. When overclocking, as long as the PCI-E is locked at 100, then the graphics card will not follow the overclocking. If the PCI-E is not locked when the CPU is overclocking, the graphics card will burn out

6. how much memory can exceed depends on the physique. Those with good physique can exceed 1500. In addition, if the memory is al channel al (non package), it is very difficult to exceed the frequency. Unless it is a package or a single memory channel, it is better to exceed the frequency