What does probation do in the correction center for the first ti

1. Generally speaking, lawyers in legal aid centers are civil servants, but there are no relevant talents in many places. Therefore, many places employ legal talents. The state has funds, donations, and the court and other organs have to pay part of the expenses, which is enough for the treatment of candidates. As for the level of legal aid centers, the government should pay part of the expenses, Generally, legal aid centers are set up at or above the county level.
legal aid centers are set up for the purpose of protecting human rights and maintaining judicial justice and balance
the Legal Aid Center (established by the judicial department) is a legal practice institution for lawyers in addition to law firms
the differences between lawyers in legal aid centers and lawyers in law firms are as follows:
the former enjoys the state salary and provides free legal services for legal aid objects, while the latter is self-employed and provides paid legal services for the society. Lawyers of legal aid centers shall not handle non aid cases, provide paid legal services to the society, and collect money and things from recipients
the former's registered lawyer certificate is called "lawyer's work certificate", while the latter's registered certificate is called "lawyer's practice certificate".

2. Complain to the labor department.

3. Xi'an

4. How to determine the magnitude and direction of the V-belt drive shaft force
in order to design the belt axle and bearing, it is necessary to work out the pressure Q (radial force, referred to as the shaft L) acting on the shaft by V-belt drive. The common formulas for calculating the shaft force Q in various literatures on belt drive technology are as follows ¨ (2) Q: Z stone_ Two watts, one hundred watts, one hundred watts, one hundred watts, one hundred watts, one hundred watts. One stroke C Zheng}, + IV min ci F= Mouth mouth. The number of Z, v-bands, F—— Suitable initial tension of single V-belt, N, F, F: tension of tight and loose sides of belt, n 0f—— The centrifugal force of the belt, N: Al / In formula (1) and (3), the pulley wrap angle is expressed in degrees, and in formula (5), it is expressed in radians. I (4) (5) (6) · 30. Journal of Hubei Institute of automotive technology No.9, 2Y - the angle between tight edge and loose edge, expressed in degrees, 2y-180. A., See Fig; P -- nominal power of V-belt drive, kW; K. - working condition coefficient; Q -- mass of V-belt per meter of belt length, kg / M; U-Band velocity, M / S; K—— Wrap angle coefficient; f—— The equivalent friction coefficient of belt drive is usually F

5. The purpose of calculating the pressure on the shaft is to select the bearing. The pressure on the shaft ultimately needs to be transferred to the bearing seat through the bearing. The bearing force is one of the important parameters to select the bearing type and calculate the bearing life
the amount of pressure on the shaft affects the use of the bearing, which has an impact on the belt drive
for reference.

6. General mechanical design manual has the design specification of belt drive. Take the ordinary V-belt as an example, 1. Select the appropriate transmission parameters (power, speed, size requirements for the shape, etc.) 2. Determine the belt type (check the selection table according to power and speed) 3. Select the reference diameter of two wheels (according to the pulley diameter series) 4. Check the belt speed 5. Determine the inner perimeter and center distance 6. Check the wrap angle 7. Determine the number of belts 8 The pretension force F = 500p (2.5 / k-1) / zv + qvv pressure q = 2zfsin (A / 2) P power, K wrap angle coefficient (look up the table), V belt speed, Q belt mass per meter, Z belt number, a small wheel wrap angle 9, friction force is not directly used in the design of wheel structure, but there are many tables to look up

7. Transmission shaft is a rotating body with high speed and less support, so its dynamic balance is very important. Generally, the transmission shaft should be tested before leaving the factory and adjusted on the balancing machine. For the front engine rear wheel drive car, it is to transmit the rotation of the transmission to the shaft of the main recer. It can be several joints, and the joints can be connected by universal joints.