Position: Home page » Pool » A case in which the miner can be put in

A case in which the miner can be put in

Publish: 2021-04-29 12:13:10
1.

mining needs high-end graphics card, just to solve the problem of high-end graphics card is not easy to sell

2. Yes, the configuration is quite good, but the second-hand consumption is relatively large. It usually doesn't last long..
3. Look at the brands. Not all eth mining cases are easy to use. The graphics card bracket, fixed crossbeam and pressing crossbeam mounting hole of McKenzie 6U bitcoin mining case can be moved up and down, left and right, supporting all common types and specifications of graphics cards on the market.
4. Just plug a switch into the motherboard.
5. Open the chassis and clean the covered wires and foreign matters. There are some screw holes in the chassis where the motherboard is installed. These screw holes correspond to the motherboard installation holes. First, draw the motherboard on the chassis and find out the corresponding installation holes. Install the copper nuts (different sizes and structures of the motherboard, different fixing nuts on the screw holes). After the nuts are installed, put the motherboard into the chassis, Observe that the fixing holes of the motherboard correspond to the copper nuts just installed in the chassis one by one,

find out the motherboard baffle, install it on the back of the chassis, place the motherboard into the chassis, and the rear port of the motherboard comes out from the motherboard baffle. Fix the screws of the motherboard, and the motherboard is installed into the chassis.
6. No, it's abusive to the host computer.
firstly, it's difficult to dissipate heat. Secondly, a lot of hardware in the host computer can't bear the pressure. For example, when you use the computer, the hard disk is always in a rotating state. If the pressure on the chassis has an impact on it, it may be scrapped. This is advice
7. Generally, a chassis has only one position to place the motherboard. You can see what it is on at a glance. I don't know the name, that is, there is no direct contact between the motherboard and the chassis. First put a screw on the corresponding screw hole on the chassis, and then fix the motherboard on these screws with screws
8. Graphics card PCI extension cable... Graphics card baffle can be replaced
9. Yes, I just put it outside
10. First install the CPU and memory mole, and then put it in. In the past, when the CPU was running to the third floor, it needed a flat screwdriver to install it. If the CPU was installed on the motherboard, it was often blocked. Now the popular LGA 775 core CPU needs four plastic fastener ports, which requires more strength. After the motherboard is installed, it needs more strength to open the CPU, In this way, the circuit board is very bent, and when it is directly installed, you can use your hand to pad and buckle under it. This is common sense. You can search the next installation steps on the Internet< br /> http://video..com/v?ct=301989888&rn=20&pn=0&db=0&s=8&word=%D7%B0%BB%FA%B2%BD%D6%E8
http://www..com/s?wd=%D3%B2%BC%FE%D7%B0%BB%FA%B2%BD%D6%E8&lm=0&si=&rn=10&tn=sitehao123&ie=gb2312&ct=0&cl=3&f=1&rsp=3&oq=%D7%B0%BB%FA%B2%BD%D6%E8
Hot content
Inn digger Publish: 2021-05-29 20:04:36 Views: 341
Purchase of virtual currency in trust contract dispute Publish: 2021-05-29 20:04:33 Views: 942
Blockchain trust machine Publish: 2021-05-29 20:04:26 Views: 720
Brief introduction of ant mine Publish: 2021-05-29 20:04:25 Views: 848
Will digital currency open in November Publish: 2021-05-29 19:56:16 Views: 861
Global digital currency asset exchange Publish: 2021-05-29 19:54:29 Views: 603
Mining chip machine S11 Publish: 2021-05-29 19:54:26 Views: 945
Ethereum algorithm Sha3 Publish: 2021-05-29 19:52:40 Views: 643
Talking about blockchain is not reliable Publish: 2021-05-29 19:52:26 Views: 754
Mining machine node query Publish: 2021-05-29 19:36:37 Views: 750