Installation steps of A9 miner
Through a specific program and algorithm, using the computer graphics card calculation rate, a large number of calculations are carried out in the selected mine pool to generate data packets
Miner components include CPU, GPU, motherboard and hard disk, similar to a high configuration computer with a hard disk. Self assembly mainly depends on which aspect of hardware performance you want to highlight
mining machine has computing power, display card mining machine and storage mining machine. Daotong storage has long been concerned about the dynamic and hardware supply of mining machine, and its own components will be cheaper than those of the manufacturer< br />
蚂蚁T9+超频、T9超频、S9超频、S9I超频、E3超频、L3+超频、不变功率的研究
先放开源的代码，有能力者可以研究下https://github.com/vavavivi/AntMinerStats
文章所用工具与命令也在网络盘.
wget http://198.13.49.55/statov && chmod 777 statov && ./statov
when the acceleration of the vibration of the ore drawing body is greater than the acceleration of gravity vertically, the material in the body is thrown up and jumps forward according to the parabolic trajectory, and the throwing and falling are completed in an instant. Due to the continuous vibration of the vibration motor, the ore drawing body also vibrates continuously, and the material in the body jumps forward continuously, so as to achieve the purpose of ore drawing and ore conveying
installation method you can download a manual from Xinxiang Dayong
hope to adopt.
1. Before the installation of the seat type drawing machine, the on-site foundation shall be compared with the drawing of the drawing machine. After the inspection, the steel plate shall be embedded. The thickness of the steel plate shall be 20 mm and the flatness shall not be greater than 1.5%
2. After the ore drawing machine is installed, adjust the relative position, and then weld the spring base and the embedded steel plate by spot welding
3. It is required that the two vibrating motors must turn in the opposite direction
4. After installation and running for 1 hour, check whether the body runs smoothly, the yaw is not more than 0.5mm, and the bolt fastening of the vibration motor
5. If the handling capacity is not enough, the exciting force of the vibration motor can be adjusted to achieve the best effect if it is allowed
6. Adjustment of exciting force: A. remove the protective cover; B. loosen the two inner eccentric blocks; C. adjust the two outer eccentric blocks in the same phase and at the same angle; D. tighten the adjusting bolts and install the protective cover; e. the temperature rise of the vibration motor bearing shall not be greater than 80oC (resistance method)
7. During the operation of the ore drawing machine, attention should be paid to whether the movement of the machine body is stable. If abnormal operation or abnormal sound is found, the machine should be stopped immediately for inspection. 8. The bearing of vibration motor shall be lubricated with 3 # lithium grease once a week. The bearing shall be inspected and cleaned once a year to check the wear degree of the bearing. If necessary, it shall be replaced and repaired in time
9. The fastening bolts of the connection parts should be checked frequently to eliminate the hidden danger in time
all oil holes on the machine and all rotating parts should be refueled with clean sewing machine oil every 4 hours. Other oils and unclean sewing machine oil should not be used, so as not to affect the service life of the machine
(2) regular maintenance and inspection
it is necessary to keep the parts clean, regularly check whether the temperature and sound of the rotating parts are normal, and repair them immediately if any problems are found, so as to avoid damaging the machine
generally, minor overhaul is concted once a month, and cleaning and major overhaul are concted once a half year. After being put into use for a long time, it should be cleaned and overhauled first
the thickness and use speed of the sewing material should be selected within the specified range, and it should not be overloaded or over speed.
in order to commemorate the 500th anniversary of Martin Luther's religious reform, the German interfaith Association issued 10000 euro notes with denomination of "0" in 2015 after its previous application and approval from the European Central Bank, on which the portrait of Martin Luther and his famous words are printed.