Ant miner plug in cable is useless
Publish: 2021-05-03 16:03:59
1. No. The mobile network can only be used as a hotspot, while the miner's requirement is to plug in the network cable.
2. 1) If it is the problem of broadband itself, first directly connect the broadband cable test. If it is the problem of broadband, contact the broadband customer service to solve it
2) if it's a problem with the router, if it can be used in the past but can't be used temporarily, my own practice is to cut off the power supply of the router and plug it in. I'll see later. If you have it, you can restore the factory settings and set it strictly according to the manual. You don't understand it and don't recommend setting it at will (this is caused by the slow or failure of the router to find the IP address under the premise of correct physical connection, not that the router is broken)
if it can't be solved all the time, it's recommended to call the customer service of the router. They have telephone online guidance. When I encounter problems that I can't solve, it's very useful to consult them. They will give correct suggestions for your setting or operation
3) if you turn off the wireless switch, just turn it on. If you use software to connect to the wireless network, it's normal that the software is not easy to use and often has problems. There's no better way. Use a router. In addition, it is caused by the network card driver is not or not suitable, whether there is a problem with the network cable interface or network cable, etc
4) if it is caused by system problems, it is recommended to restore the system or re install it.
2) if it's a problem with the router, if it can be used in the past but can't be used temporarily, my own practice is to cut off the power supply of the router and plug it in. I'll see later. If you have it, you can restore the factory settings and set it strictly according to the manual. You don't understand it and don't recommend setting it at will (this is caused by the slow or failure of the router to find the IP address under the premise of correct physical connection, not that the router is broken)
if it can't be solved all the time, it's recommended to call the customer service of the router. They have telephone online guidance. When I encounter problems that I can't solve, it's very useful to consult them. They will give correct suggestions for your setting or operation
3) if you turn off the wireless switch, just turn it on. If you use software to connect to the wireless network, it's normal that the software is not easy to use and often has problems. There's no better way. Use a router. In addition, it is caused by the network card driver is not or not suitable, whether there is a problem with the network cable interface or network cable, etc
4) if it is caused by system problems, it is recommended to restore the system or re install it.
3. There are several reasons why the network cable is inserted into the network port and there is no response
1. The network cable is blocked, and there is a breakpoint in the middle
2. The switch or router on the network cable is not connected to the power supply
3. The crystal heads at both ends of the network cable are faulty
4. There is no network in the router or switch on the network cable
note: it's better to start from the host computer and look up one level at a time
solutions:
1. Connect the breakpoint or replace the network cable
2. The router or switch is connected to the power supply
3. Replace the crystal heads at both ends of the network cable
4. Reset the upper router to access the network.
1. The network cable is blocked, and there is a breakpoint in the middle
2. The switch or router on the network cable is not connected to the power supply
3. The crystal heads at both ends of the network cable are faulty
4. There is no network in the router or switch on the network cable
note: it's better to start from the host computer and look up one level at a time
solutions:
1. Connect the breakpoint or replace the network cable
2. The router or switch is connected to the power supply
3. Replace the crystal heads at both ends of the network cable
4. Reset the upper router to access the network.
4. There are many reasons why there is no signal
1. The cable itself is not connected to the Internet
2, the network is in arrears
3, there is a problem with the network cable
4. There is something wrong with the computer
5, there is a problem with the router.
1. The cable itself is not connected to the Internet
2, the network is in arrears
3, there is a problem with the network cable
4. There is something wrong with the computer
5, there is a problem with the router.
Hot content