How does assembly miner always cut off power automatically
Publish: 2021-05-06 17:50:10
1. 1. The high-pressure fault of the air conditioner caused the protection shutdown. The reason may be that the weather is too hot, the radiator of the outdoor unit is dirty and blocked, and the heat can not be dissipated. It is for this reason that the machine can only be started after the power is removed for a few minutes. After the shutdown, the pressure is restored to balance, and the machine cools down, so it can be started. It is recommended to clean the radiator of outdoor unit and spray water with clean water or air conditioner cleaning agent. 2. Fan problem. If the air conditioning compressor and Freon are basically normal when the machine is just started, check whether the speed of the external fan is normal. If the external fan doesn't run or the speed becomes slow, the normal operation of the air conditioner will be affected. The current will increase and the load of the air conditioner will be too heavy.
2. You need professional chips to assemble mining machines. If you want to buy chips, I suggest you buy Avalon's third generation chips directly. But the assembly of mining machine is a very troublesome thing, the technical requirements are higher, but if you do not have professional technical strength, it is recommended that you buy mining machine directly. If you want to be an OEM, you can directly buy chips and other materials for assembly. At present, avalon3 is about to be put into the market. It is suggested to buy avalon3 directly.
3. Generally speaking, press the three keys of Ctrl + Alt + delete
the specific operation methods are as follows:
1. Judge that the machine is in a dead state. The way to change the state is to press the NumLock key to see if the num light will change the state with the pressing of the key. If it doesn't change, it will be in a crash state
2. If the machine is in a dead state, press the CTRL and ALT keys with your left hand, and then press the delete key with your right hand while keeping pressing
3. The system will restart.
the specific operation methods are as follows:
1. Judge that the machine is in a dead state. The way to change the state is to press the NumLock key to see if the num light will change the state with the pressing of the key. If it doesn't change, it will be in a crash state
2. If the machine is in a dead state, press the CTRL and ALT keys with your left hand, and then press the delete key with your right hand while keeping pressing
3. The system will restart.
4. Mining may be able to dig, but the probability is relatively small, generally the main jewelry is selected by mineral processing skills. Jewelry dressing skills randomly proce green and blue stones.
5. blockchain technology is now involved in many application fields, such as finance, logistics, medical and other instries. For example, blockchain technology uses electronic bills to view all medical bills with one click; For example, the okex exchange can buy digital currency to increase wealth. Blockchain technology is still in development, I believe it can bring more surprises.
6. 1、 The temperature of the main bearing is too high, resulting in pitting corrosion or melting.
2. Causes: the nut fixing the liner is loose, the gasket is damaged, the screw is broken, the liner is damaged or falls off, etc
Troubleshooting: tighten or replace the bolts, add sealing washer, and replace the liner if necessary. 1. The sound in the mill is reced or increased
the main reason for the weakening of the sound in the grinding machine is too much feeding, too large blocks, the feeding amount is greater than the discharge amount, and the grinding machine begins to swell. The method of elimination was treated according to the method of elimination of abdominal distention
the increased sound in the mill may be e to too little feeding, resulting in empty grinding, and the medium directly strikes the liner or the medium strikes each other. When the feeding is normal and the sudden sound intensifies, it is caused by the lining plate or grid plate falling off
elimination method: increase the feeding amount; If the liner falls off, stop the machine immediately to replace or reassemble the liner. 2. The grinding machine suddenly proces strong vibration and impact sound. One of the following reasons will cause the above phenomenon: 1) iron impurity mixed in the gear gap
elimination method: stop the car immediately, remove the iron whoring, and trim the tooth surface. 2) The pinions move in tandem and collide with the gearbox. Elimination method: stop immediately, replace the gearbox and fix the gear along the axial direction again
3) the gear is damaged. Elimination method: stop immediately and replace the gear. 4) The bearing or anchor bolt is loose
elimination method: first adjust the gear to make the big and small gears mesh correctly, and then tighten the bolts
the above is provided by Lizhuo machinery! For reference only!
2. Causes: the nut fixing the liner is loose, the gasket is damaged, the screw is broken, the liner is damaged or falls off, etc
Troubleshooting: tighten or replace the bolts, add sealing washer, and replace the liner if necessary. 1. The sound in the mill is reced or increased
the main reason for the weakening of the sound in the grinding machine is too much feeding, too large blocks, the feeding amount is greater than the discharge amount, and the grinding machine begins to swell. The method of elimination was treated according to the method of elimination of abdominal distention
the increased sound in the mill may be e to too little feeding, resulting in empty grinding, and the medium directly strikes the liner or the medium strikes each other. When the feeding is normal and the sudden sound intensifies, it is caused by the lining plate or grid plate falling off
elimination method: increase the feeding amount; If the liner falls off, stop the machine immediately to replace or reassemble the liner. 2. The grinding machine suddenly proces strong vibration and impact sound. One of the following reasons will cause the above phenomenon: 1) iron impurity mixed in the gear gap
elimination method: stop the car immediately, remove the iron whoring, and trim the tooth surface. 2) The pinions move in tandem and collide with the gearbox. Elimination method: stop immediately, replace the gearbox and fix the gear along the axial direction again
3) the gear is damaged. Elimination method: stop immediately and replace the gear. 4) The bearing or anchor bolt is loose
elimination method: first adjust the gear to make the big and small gears mesh correctly, and then tighten the bolts
the above is provided by Lizhuo machinery! For reference only!
7. The air switch is small, but the wires at home should be able to bear it, otherwise it is dangerous
8. There is something wrong with the mobile phone system. Reset down the normal management of the phone is good. First download the app, Google software to operate the good. Connect the mobile phone to the computer, select the tool stable settings, the mobile phone is OK. Click on the mobile phone system upgrade version set to the latest OK. That will ensure that the mobile phone is updated to the latest version. In this way, you can enter the management interface and operate normally.
Hot content