How to change the fan speed of T2T mining machine

1. No matter what motherboard you use,
fan speed in BIOS can't be changed,
the automatic adjustment of fan speed is determined by the temperature of CPU. When the CPU temperature is high, the fan speed will increase, and when the CPU temperature is low, the fan speed will automatically decrease. This is a motherboard with automatic speed adjustment. The other is without adjustment, the fan speed is always the same.

2. BIOS can't be adjusted. It can only set the temperature of the CPU. If the heat dissipation is not good, the temperature can't fall down. It will work hard all the time. Of course, it will ring

3. Specific methods: 1. Enter power under BIOS, set cpufan mode setting to auto and restart. First, set the fan to automatic mode, check the speed and sound after power on. If it is acceptable, it is best to use this mode. If not, go on

2. Set manual mode in cpufan mode setting, and cpufan is set to 100-150 (the default is 250). In this way, the fan speed will drop to 1800-2400, and the noise will be much less. But at this time, the fan does not adjust the speed intelligently, that is, the speed is a certain value

3: set the intelligent speed regulation, cpufan target temp Valun - 40 cpufan startup value - 40, that is, the CPU temperature reaches 40 ° Then start intelligent speed regulation

4 cpufan stop value --- 35, that is, the CPU temperature reaches 35 ° After that, stop the speed regulation, and then rece the speed! Note: ring the whole adjustment process of the fan, you need to detect the CPU temperature. If it is too high or crashes, you should immediately stop changing the fan to the original default setting. If so, it means that your fan power is small and you can't rece the speed. You need to buy another radiator

4. What's the trouble? Just download any version and use Kepler biostweaker to change it to the effect you want. I change it to the effect I want on the official website. For example, I change the fan from 30-80 to 0-100

5. CPU fan plug four pin power plug will automatically intelligent speed! The plug should be four pin

6. There are several ways to change the speed of CPU fan:
1.
select 4-pin intelligent cooling fan, which supports PWM speed regulation and can be easily adjusted through BIOS and software provided by motherboard manufacturer<
2.
BIOS on the motherboard supports fan voltage speed regulation, which can support ordinary 3-pin fan, but supports several fixed modes, such as full speed, half speed and stop<
3.
special fan speed regulator is installed. High grade chassis or special chassis have n fans, and the sockets on the main board are obviously not enough. The chassis will be equipped with fan speed regulator or need its own speed regulator to control the noise and heat dissipation balance of the fan<
4.
it is the third beggar's version to add a speed regulating adapter line to the CPU fan. The so-called speed regulating line is the connecting line of series resistance, which can rece the fan speed by increasing the line resistance<
5.
CPU cooling fan with large cooling area and parallel speed is used. This kind of CPU radiator has been designed with low speed and balance of heat dissipation and noise. It's easy.

7.

Here is how to adjust the fan speed of card a:

1. Click "amd catalyst control center" in the blank space of the desktop

8.

Method 1: first of all, open the chassis, screw the fixed screw of the graphics card, then remove the graphics card, clean the st of the graphics card fan and add some lubricating oil, and then install it back

method 2: if your graphics card supports speed regulation, we can set it in the BIOS, generally not. You can try to download software or graphics card with the tools to modify the speed

method 3: you can buy a video card fan governor, and then install it

9. Scheme 1: take line 3 of Longgang Metro Line
at Longgang, get off at Buji via 14 stops, change to line 5 of central line of Metro ring line
, get off at Xili via 12 stops, walk about
232
meters, take No. 240 at Xili Hospital East, get off at xilihu terminal via 5 stops, and walk about
1267
meters to Shenzhen wildlife park

10. The only direct train is 361 in longgangge
then it is suggested that you transfer faster. Although there are many stops, the distance is shorter
:
Longgang Tianhong shopping mall
take bus No. 366 (12 stops)
to Buji checkpoint
get off, and then transfer to bus No. 240 (31 stops)
to the zoo