Which pit is L3 digging in

1.

In fact, the coins that can be g up every day are different. When L3 + first came out, it was able to dig one Wright coin every day. Now the computing power of the whole network has been greatly improved, and about 0.54 yuan can be g every day. It mainly depends on the comparison between your computing power and that of the whole network

bitcoin mining machine is a kind of computer used to earn bitcoin. This kind of computer generally has professional mining chips and works in the way of burning graphics card, which consumes a lot of power. It is one of the ways to get bitcoin that users download software from personal computer and then run specific algorithm to get corresponding bitcoin after communicating with remote server

2. The popular digital currencies in 2013 are bitcoin, Leyte coin, zeta coin, pennies (Internet), invisible gold bar, red coin, pole coin, barbecue coin and prime currency. At present, hundreds of digital currencies are issued all over the world

Output value: according to the calculation formula of bitcoin output, almost every four years, the output will be halved, and finally reach the extreme value of 21 million. At this time, there will be a substantial appreciation. This kind of currency without the control of the central bank, compared with the real currency of quantitative easing, will continue to appreciate. By 2013, about 11 million bitcoins had been proced

extended data:

1. Ant mining machine is the first cryptocurrency mining machine brand in the world, with a market share of about 70%. The mining machine is developed by bitmainland and has a patent in mainland China. At the beginning, ant miner had only bitcoin miner. Later, its business expanded to other cryptocurrencies, such as Ethereum, dascoin, Leyte, Monroe, etc

Ant miner adopts ASIC chip designed by bitcontinental, which is proced by TSMC. All chips are made of BM prefix. Each miner has three to four circuit boards, and there are dozens of chips on the circuit board. Therefore, each miner can only be used to mine one or more cryptocurrencies using the same algorithm

3. Ant mining machine needs special mining software, and can not use third-party software. In addition, because of its high power, the ant miner also needs to be used with a special fire ox

2. Are you going to dig after the mine disaster

4. Now we can't dig it down. There are 21 million in total. It's almost done. We can't say how long we can get one. It depends on the computer's daily and monthly calculation. It's hard to say how long luck will come to you.

5. In fact, the coins that can be g up every day are different. When L3 + first came out, it was able to dig one Wright coin every day. Now the computing power of the whole network has been greatly improved, and about 0.54 yuan can be g every day. It mainly depends on the comparison between your computing power and that of the whole network

6. Grate kiln pellet is the flue gas of sintering machine< The characteristics of flue gas are as follows:
(1) the annual operation rate of sintering machine is high and the flue gas emission is large
(2) the composition of flue gas is complex, and there is variability according to the change of ingredients
(3) the flue gas temperature fluctuates greatly in the range of 90-150 ℃< (4) the humidity of flue gas is relatively high, generally about 10%
(5) e to the relationship between sulfur content of sintering raw materials, the SO2 concentration of flue gas changes greatly with the change of proportioning ratio 6) The oxygen content of sintering flue gas is high, about 10% - 15%
(7) it contains corrosive gases, such as hydrogen chloride (HCl), sulfur oxides (SOx), nitrogen oxides (NOx), hydrogen fluoride (HF), etc

7. During the commissioning process, unified coordination and special person command are required< br /> All personnel participating in the test run must obey the unified arrangement and command of the on-site commander, and no one is allowed to operate at will or against rules< br /> The operators participating in the test run must stick to their posts and shall not leave their posts without authorization< br /> You must confirm that you have received the start-up instruction before you can start according to it. It is not allowed to start or stop the machine at will, but in case of failure of the running equipment, it shall stop the machine immediately and report to the commander< br /> Non commissioning personnel (including Party A) are strictly prohibited to enter the commissioning site. During the trial operation of the equipment, obvious safety signs must be set in the trial operation area, and special personnel shall be assigned to take care of them< br /> The safety signs hung in the trial operation area must be picked up by the person who hangs them. No one is allowed to pick up and hang the safety signs without authorization. All personnel who take care of the safety signs must stick to their posts and perform their ties< br /> The personnel participating in the test run must wear safety protection articles according to the regulations, and the clothes that are easy to be involved by machinery must be tied tightly to prevent being strangled< br /> The no-load test run must be carried out according to the test run plan. The equipment, operating devices, interlocking devices and contact signals shall be adjusted and inspected item by item. The equipment, no matter big or small, must be inspected by the mechanical and electrical professionals. After confirming that the above conditions are met, the test run commander shall give the start-up order, It is absolutely forbidden for non professionals to drive without authorization and other people to drive by force< br /> Before the test run, it is necessary to check in detail whether parts, tools and other sundries are left in the equipment, whether all safety devices are reliable, and whether other personnel retreat beyond the safe distance< br /> Before the test run, check whether the lubricant has been added to the moving parts according to the requirements. During the test run, pay attention to observe the lubrication of the bearing parts. If there is a lack of oil, stop the machine in time< br /> During the test run, no one is allowed to touch the moving parts, and no adjustment is allowed to the running equipment. If the adjustment is necessary, it must be stopped. If it is necessary to adjust ring operation, it must be approved by the commanders and take appropriate safety precautions to prohibit wearing gloves. br /> During the trial operation of all equipment, it should be carried out in strict accordance with the safety technical regulations. During the operation, it is not allowed to scrub and repair, and it is strictly forbidden to extend the head and hand into the range of mechanical travel< br /> During the trial operation of the equipment, it is strictly forbidden to cross or over the equipment in operation. It is necessary to walk on the fixed cross bridge or aisle. It is strictly forbidden to ride on the belt conveyor and other equipment< br /> During the operation of the equipment, if abnormal phenomena such as abnormal sound and vibration are found, the equipment shall be stopped immediately. After the power supply is cut off, the equipment shall be checked to confirm that the accident has been handled. After the maintenance personnel leave the site, the commissioning commander shall direct the operation. It is strictly forbidden to operate with faults< br /> After the test run of the equipment, the power supply from each control room to the workshop must be cut off to avoid equipment accidents< br /> It is hoped that all commissioning personnel must strictly abide by the above commissioning safety operation proceres to ensure the safe and smooth commissioning.