1800W Great Wall power supply for mining machine
Publish: 2021-04-08 05:55:34
1. It depends on the power consumption superposition of the specific graphics card. The power supply is not always full output, but according to the demand. Now the 1080 single card is 180W, with six 100% running, it is 1080W, plus the power consumption superposition of other hardware. But I've only heard that the demand for password cracking machines is so high. I can't see such machines.
2. Is it one of the following games, StarCraft, red alert, Warcraft, Empire
3. It's normal for you
1) ant S3 miner, I saw several comments from friends in the Forum
the official power consumption is 332w, and businesses usually report 355w
the actual power consumption is about 390W
2) your power supply is rated at 500W, which is basically 400W after decting the conversion loss
theoretically, it should be able to drive,
however, for the consideration of long-term stability, the miner generally requires higher power supply when designing
the fault tolerance between 390W and 400W is less
therefore, we all use 600W rated power supply in the forum and online evaluation
(Rated 600, not the highest 600)
the stability of mining machine is very important. A stable and suitable power supply will definitely save you a lot of trouble in the future
some suggestions for your reference
1) ant S3 miner, I saw several comments from friends in the Forum
the official power consumption is 332w, and businesses usually report 355w
the actual power consumption is about 390W
2) your power supply is rated at 500W, which is basically 400W after decting the conversion loss
theoretically, it should be able to drive,
however, for the consideration of long-term stability, the miner generally requires higher power supply when designing
the fault tolerance between 390W and 400W is less
therefore, we all use 600W rated power supply in the forum and online evaluation
(Rated 600, not the highest 600)
the stability of mining machine is very important. A stable and suitable power supply will definitely save you a lot of trouble in the future
some suggestions for your reference
4. If you want to use the switching power supply of the computer for other purposes, you can change it as follows:
1. Open the iron box of the power supply, take out the circuit board from the box, and use a brush to remove the st
2. Find the key components. Including: power oscillation integrated block, optocoupler, 12V voltage regulator, pulse width adjusting potentiometer, etc. Find the information of power supply mole
3. First, change the 12V voltage regulator into 15V, and find the pulse width adjustment circuit according to the data of power supply integrated block. Some power supplies do not design power supply fine-tuning, but fixed resistance. Remove the fixed resistance, and connect a potentiometer whose resistance value is basically close to the welding resistance on the two solder joints. Now adjust the resistance of the potentiometer to the maximum
4. Use a multimeter to monitor the 12 V power supply port, turn on the power supply, slowly rece the resistance of the potentiometer, observe the voltage change, and adjust it to 15 v. After stabilization, observe for a little time and connect the false load toaster
5. After it is accurate, measure the resistance of the potentiometer and replace it with a fixed resistance with the same resistance.
1. Open the iron box of the power supply, take out the circuit board from the box, and use a brush to remove the st
2. Find the key components. Including: power oscillation integrated block, optocoupler, 12V voltage regulator, pulse width adjusting potentiometer, etc. Find the information of power supply mole
3. First, change the 12V voltage regulator into 15V, and find the pulse width adjustment circuit according to the data of power supply integrated block. Some power supplies do not design power supply fine-tuning, but fixed resistance. Remove the fixed resistance, and connect a potentiometer whose resistance value is basically close to the welding resistance on the two solder joints. Now adjust the resistance of the potentiometer to the maximum
4. Use a multimeter to monitor the 12 V power supply port, turn on the power supply, slowly rece the resistance of the potentiometer, observe the voltage change, and adjust it to 15 v. After stabilization, observe for a little time and connect the false load toaster
5. After it is accurate, measure the resistance of the potentiometer and replace it with a fixed resistance with the same resistance.
5. Good power supply, 80plus gold medal certification, this power supply now has a lot of second-hand online sales, mining machine down, internal component configuration has shrunk and aging, buy time to pay attention to.
6. If it is much lower than the original price, there is such a suspicion
Hot content