Miner jammer
Publish: 2021-04-15 14:26:30
1. Generally speaking, press the three keys of Ctrl + Alt + delete
the specific operation methods are as follows:
1. Judge that the machine is in a dead state. The way to change the state is to press the NumLock key to see if the num light will change the state with the pressing of the key. If it doesn't change, it will be in a crash state
2. If the machine is in a dead state, press the CTRL and ALT keys with your left hand, and then press the delete key with your right hand while keeping pressing
3. The system will restart.
the specific operation methods are as follows:
1. Judge that the machine is in a dead state. The way to change the state is to press the NumLock key to see if the num light will change the state with the pressing of the key. If it doesn't change, it will be in a crash state
2. If the machine is in a dead state, press the CTRL and ALT keys with your left hand, and then press the delete key with your right hand while keeping pressing
3. The system will restart.
2. If it doesn't crash immediately, just use the old method to turn off the fan and pull it out one by one to try. The heat increase will make the faulty graphics card crash faster, so that the faulty one can be found as soon as possible. However, isn't bitcoin banned in China
3. 1 whether the power supply provides enough power
2 whether the graphics card overclocking parameters are correct
3 whether the temperature control and cooling are normal
2 whether the graphics card overclocking parameters are correct
3 whether the temperature control and cooling are normal
4. Of course, it's the mainland. Wu Jihan was born in mining
5. I think the power supply is small. Are you six of the same graphics cards? According to the full load of 350W, six power sources should be more than 2000W. Crash is a sign of insufficient power.
6. Cone crusher jam is often e to some sudden equipment failure, mainly in three places:
1, blocking material stuck
1, cone crusher feeding too much, or feeding properties do not meet the requirements, resulting in cone crusher blocking material, will make the crusher work electricity flow, circuit automatic protection and stop the machine, Even the cone crusher may be stuck and forced to stop
2. When iron or other non breakable materials enter the crushing chamber of the cone crusher, it will also cause the material blocking and even equipment blocking< 1. Improper use of the cone crusher is one of the main reasons for the fracture of the main shaft. For example, in order to achieve the required discharge fineness, the discharge port is constantly tightened, and if there are non breakable materials entering the crushing chamber, the main shaft will have a sharp impact, resulting in the fracture of the main shaft of the cone crusher
2. On the other hand, when the cone crusher is in overload operation for a long time, although there is overload protection device, it can not completely avoid the damage to the equipment, and the main shaft is prone to fracture, leading to the equipment stuck< When the cone crusher is running with load, the locking failure is caused by the pressure loss of the hydraulic station, and the adjusting sleeve will rotate with the moving cone. If the post personnel do not find and deal with it in time, it will cause the phenomenon of adjusting sleeve stuck, which will lead to the shutdown of cone crusher
2. The causes of adjusting sleeve sticking may be poor thread lubrication, wear of adjusting cap seal or st cover seal, scratch of adjusting sleeve and support sleeve thread, or long-time overload of cone crusher, etc.
1, blocking material stuck
1, cone crusher feeding too much, or feeding properties do not meet the requirements, resulting in cone crusher blocking material, will make the crusher work electricity flow, circuit automatic protection and stop the machine, Even the cone crusher may be stuck and forced to stop
2. When iron or other non breakable materials enter the crushing chamber of the cone crusher, it will also cause the material blocking and even equipment blocking< 1. Improper use of the cone crusher is one of the main reasons for the fracture of the main shaft. For example, in order to achieve the required discharge fineness, the discharge port is constantly tightened, and if there are non breakable materials entering the crushing chamber, the main shaft will have a sharp impact, resulting in the fracture of the main shaft of the cone crusher
2. On the other hand, when the cone crusher is in overload operation for a long time, although there is overload protection device, it can not completely avoid the damage to the equipment, and the main shaft is prone to fracture, leading to the equipment stuck< When the cone crusher is running with load, the locking failure is caused by the pressure loss of the hydraulic station, and the adjusting sleeve will rotate with the moving cone. If the post personnel do not find and deal with it in time, it will cause the phenomenon of adjusting sleeve stuck, which will lead to the shutdown of cone crusher
2. The causes of adjusting sleeve sticking may be poor thread lubrication, wear of adjusting cap seal or st cover seal, scratch of adjusting sleeve and support sleeve thread, or long-time overload of cone crusher, etc.
7. If the owner rents the computer to others as a server / mining machine, the computer will definitely get stuck.
How can these companies make profits if they don't use your computer resources? And they want to make profits by using your computer resources as much as possible for uploading, downloading, computing, etc. when the software takes up too much of the system hardware, the computer will naturally get stuck
the problem can be solved by shutting down the software and then uninstalling it. It is not recommended to install this kind of useless software. The gain is not worth the loss.
How can these companies make profits if they don't use your computer resources? And they want to make profits by using your computer resources as much as possible for uploading, downloading, computing, etc. when the software takes up too much of the system hardware, the computer will naturally get stuck
the problem can be solved by shutting down the software and then uninstalling it. It is not recommended to install this kind of useless software. The gain is not worth the loss.
8. What about the picture???????
Hot content