PX miner

1. Model and specification: ккд— 700 (px-700 / 130) feed mouth 700 mm
2. Feed and discharge particle size: feed particle size: & lt; 550 mm; Ore size: 100-160 mm
3. Type: suspension shaft type
4. Transmission mode: the motor is decelerated by V-belt pulley and connected to the transmission shaft by elastic coupling
5. Maximum lifting capacity of crushing cone: 160mm
6. Eccentricity: upper eccentricity: 21.61mm; Lower eccentricity: 33.37 mm
7. Motor model jr127-8, 130 kW, 735 rpm
8. Shaft speed: 406 rpm
9. Eccentric sleeve revolution, 140 rpm
10. Proction capacity: when the discharge port is 130 mm, the proction capacity is about 300 t / h
11. Lubrication mode: oil pump
12. Overall dimension: 2800 × five hundred and fifty-five × 4415
13. Total weight: 33706kg. 1. Overload operation of equipment is not allowed, such as too much or too large ore feeding, too small ore outlet, etc
2. The maximum lump size of ore feeding should not exceed 80-85% of the width of ore feeding mouth
3. The adjusting gap of the ore outlet should be within the range of 100-160 mm (the crushing cone is 1:3, that is, the crushing cone rises by 6 mm and the ore outlet decreases by 1 mm)
4. It is strictly forbidden for metal iron and other foreign matters to enter the crusher cavity ring operation. If they enter, they should be stopped immediately for elimination. 1. Check whether there is enough lubricating oil in the oil tank, whether the oil quality meets the requirements, and whether the oil filter is not clean
2. Test the oil pump and check whether there is oil leakage in the oil pump and pipeline
3. Whether the oil pressure is between 0.8-1.5kg/cm2
4. Check whether the oil return is not smooth and the oil flow is unstable
5. There is no looseness in the foundation screw of each part of the machine body and the frame interface screw in the frame
6. Whether the screws, pulley and key of the transmission shaft are loose
7. If there are any materials in the crusher chamber, it must be removed before starting
8. Whether the easily worn parts of the engine body (such as broken cone liner and middle frame liner) are seriously worn or cracked
9. Check whether the funnel is blocked or seriously worn
10. Check whether the hand wheel of oil immersed rheostat in electrical part is at zero position
11. Check the contact condition of motor carbon brush
12. It is not flexible to check the distribution box and operating mechanism
13. Check whether the pointer of ammeter is at zero. 1. Operation method of the equipment
(1) before operation, the equipment must be inspected item by item according to the inspection content
(2) start the oil pump first, and start the motor only after the return oil is normal
(3) pay special attention to the sound of motor and crusher when starting, and stop running immediately in case of any abnormality
(4) start feeding after normal operation of the equipment
(5) ore feeding must be stopped when the operation is stopped, and it can only be stopped when there is no ore in the crushing chamber
(6) stop the oil pump feeding
2. Start up operation sequence:
(1) first check whether the oil immersed rheostat is at the zero position and whether the short-circuit switch is open
(2) press the start button
(3) slowly transfer the hand wheel of the oil immersed rheostat to the starting position until the motor reaches the rated speed
(4) close the short circuit breaker
(5) observe whether the indication of ammeter is normal
(6) the motor shall not be started frequently, and generally it shall not be started more than three times continuously
3. Stop operation sequence:
(1) stop feeding before stop, and stop the crusher when all ores in the crusher cavity are discharged
(2) the operator presses the stop button
(3) turn the hand wheel of the oil immersed rheostat back to the zero position and open the short-circuit knife switch
(4) after power failure without notice or shutdown with load, the ore in the crusher cavity must be taken out to facilitate the start-up after power supply

The official definition of ball mill model and specification is a series of indicators reflecting the nature, performance and quality of the proct, which is generally composed of a series of letters and numbers with a certain number. For example, brand name, grade, composition, content, purity, size, etc. In short, specification refers to the size of performance indicators, and model refers to the name (or code) obtained from the collection of specifications and models

ball mill specification: if it is expressed by the diameter and length of the ball mill cylinder, it can be shown as φ two point two × 7m、 φ two point four × 13m、 φ three × 11 m, etc

ball mill model: also, according to the diameter and length of the ball mill cylinder, it is mqgg 1212, mqG 1212, mqy 1212, mqyg 1212, etc., in which the letter part indicates the abbreviation of the ball mill equipment, and the number part indicates the diameter of the ball mill cylinder. Take mqgg 1212 as an example: this model is a wet energy-saving lattice ball mill φ one point two × 1.2m

generally, there are many models and specifications of mine ball mills, which can be divided into large, medium and small types according to the level. Taking ferrous metals as an example, a large concentrator with a daily processing capacity of 3000t, a medium concentrator with a daily processing capacity of 900-3000t, and a small concentrator with a daily processing capacity below 900t

the commonly used mining ball mill equipment mainly includes

wet energy-saving lattice ball mill. This lattice ball mill mostly deals with coarse minerals and adopts large double row self-aligning roller bearing, which effectively reces the friction force and is easy to start. Compared with other ball mills, it can save 20-30% energy

small ball mills are mainly used in small and medium-sized development enterprises. The proction scale of such enterprises is small, and the investment cost of small ball mills is low, so the investment income of users is fast, and it will not cause a waste of resources. The main ball mill equipment and model parameters suitable for medium-sized concentrator are as follows:

the above introces the definition of mining ball mill model and specification, and the distinction of model and specification according to large, medium and small type selection, and shows the model, specification and parameters of ball mill according to each level, which can be used for reference. However, in the actual concentrator, the specific model and specification of ball mill selected by each concentrator should consider the nature of materials and beneficiation conditions. It is recommended to select qualified ball mill manufacturer for test selection< br />