Gama770s3 main board mining
2. Make sure there is no foreign matter in the memory slot. Brush the memory slot several times with a hard bristled toothbrush with moderate strength, and then suck it with a vacuum cleaner or blow it with the cold air of the air ct
3. Check the contact between the motherboard and the chassis to see if the memory pins on the back of the motherboard may contact the chassis, causing a short circuit
4. I believe you have wiped the golden finger of the memory, please wipe it carefully
5. If none of the above actions can solve the problem, it needs to be repaired. The fault may be that the power supply voltage of the memory is insufficient, or there is a short circuit in the memory slot. Anyway, it's not a big problem, and the maintenance cost will not be too high
6. I used to have an AM2 motherboard, which was in a similar situation. The memory slot was good and bad from time to time. I went to repair and diagnosed it as unstable voltage, and the maintenance cost was 20 yuan.
North Bridge chip amd 770
South Bridge chip AMD SB600
CPU slot AM2 +
support CPU type support am2940 series processor
motherboard architecture ATX
front end bus frequency 2.6GHz
support memory type DDR2
support channel mode support
memory slot 4 DDR2 DIMM
memory frequency DDR2 1066MHz
maximum support memory capacity 16g
support
On board sound card on board Realtek alc888 7.1 channel sound card
on board network card on board Realtek 8111b gigabit network card
expansion parameters
hard disk interface ATA 100, ATA 133, s-ata150, s-ata II
number of sataii interfaces 6
disk array type SATA
disk array mode RAID 0, RAID 0 + 1, RAID 1
supports graphics card standard PCI 2.0
expansion slot 1 × PCI Express X16,4 × PCI Express X1
PCI slot 2 × PCI
expansion interface, keyboard PS / 2, mouse PS / 2, USB2.0, RJ45 network card interface, coaxial audio, COM interface, IEEE 1394a
number of USB interfaces 8
other parameters
power circuit 4-phase circuit
power interface 24pin + 4Pin
overall dimension 30.5 × 21.0cm
HyperTransport bus technology supports HyperTransport bus technology
1. Symmetric al channel working mode
symmetric al channel working mode requires that the memory capacity of two channels is equal, but there is no strict requirement for absolute symmetry of memory capacity. A channel is 512MB + 512MB, B channel is 1GB, As long as the total capacity of channel A and channel B is equal. In this mode, two, three or four memory moles can be used to obtain the al channel mode. If the speed of the memory mole used is different, the speed of the memory channel depends on the speed of the slowest memory mole installed in the system. The details are as follows:
(1) absolute symmetry of memory mole. This is the most ideal symmetrical al channel, that is, insert memory moles of the same capacity into the slots of the same color, and the number of memory moles is 2 or 4. In this mode, all memory works in al channel mode, and the performance is the strongest< (2) symmetry of memory capacity. This mode does not require that the number of memory moles in the two channels is equal. It can be composed of three memories. The total memory capacity of the two channels is equal, and all the memories work in the al channel mode< Asymmetric al channel mode
in asymmetric al channel mode, the memory capacity of the two channels can be unequal, and the memory capacity of the al channel depends on the channel with smaller capacity. For example, if channel a has 512MB of memory and channel B has 1GB of memory, then 512MB in channel A and 512MB in channel B form a al channel, and the remaining 512MB of memory in channel B still works in single channel mode. It should be noted that the two memories must be inserted in the same color slot.
BIOS upgrade can support AM3 processor CPU_ Socket AM2 + / AM3 supports CPU number 1 bus frequency supports ht3.0 bus memory specification memory type DDR2 Memory description supports al channel DDR2 1066 (OC) 800 / 667 memory, supports up to 16GB expansion slot, graphics card slot PCI-E 2.0 16xpci slot, 2 PCI slots, 4 PCI-E 1xide slots, 1 ide slot, FDD slot, 1 FDD slot, connected with floppy drive SATA interface, 6 sataii interfaces, supports SATA raid 0,1, 0 + 1 I / O Interface USB interface 12 USB2.0 interface PS / 2 interface PS / 2 mouse, PS / 2 keyboard interface other interfaces 2 IEEE 1394 interfaces / 1 s / PDIF coaxial output / 1 s / PDIF optical output / 1 RJ45 network interface external port audio interface board type main board type ATX board type overall dimension 30.5cm × 21.0cm Software Management BIOS performance two 8Mbit flash
use authorized award BIOS
support al BIOS< br />PnP 1.0a、DMI 2.0、SM BIOS 2.4、 ACPI 1.0b other features other features support BIOS
support download center
support q-flash
support easytune
support Xpress install
support Xpress recovery2
support virtual al BIOS other parameters hardware monitoring CPU / system temperature detection
CPU / system / power fan speed detection
CPU over temperature warning
CPU / system / power fan fault alarm The CPU intelligent fan control power socket parameter correction, a four pin, a 24 pin power interface, power supply mode five phase
indeed. Amd supports memory models, and the controller is not on the motherboard. Inside the CPU, AMD's memory controllers are all downward compatible
but is it so easy to change the motherboard slot
let's not say that the pins of the two motherboards are different. Is the wiring between the motherboard and the new memory slot the same? The working voltage of the two kinds of memory is also different. How can we bury it in another pit!
if it is version 2.0, it can support phenom
II
X6
1100t, but it must be updated to FDE version BIOS
if it is version 1.0, it can only support phenom
X4
9850
95w version, and it must be updated to F6 version BIOS.
As of December 2016, the bus timetable from Shenzhen Baoan Shajing central passenger station to Guangxi Wuzhou is as follows: