W10 mining auto restart
Publish: 2021-05-05 00:55:17
1. The solution steps are as follows:
1. Set the system error function. Right click my computer - properties - system properties advanced - startup and recovery - Settings - startup and recovery - remove the "auto restart" option in the "system failure" column
2. Check if the main board battery voltage is too low, and replace the battery; Set the BIOS to the factory default
3. Set up power management. Click "start - Settings - control panel - Power Options". In the pop-up window, enable or cancel "advanced power support" as needed. If you use "advanced power support" when a fault occurs, try to cancel it, otherwise, enable it
4. The memory may be damaged or in poor contact, or the memory slot of the motherboard is faulty. Use the eraser to clean the memory slot and replace the memory that is suspected to be faulty
5. If you have a USB device connected to your computer, unplug it first and then turn it off. Or in BIOS, set restore AC power loss of power management setup in BIOS to disabled and PM control by APM of power management setup to yes
6. If the system files are missing, please refer to the system ghost base installation tutorial www.ghost008.com/jiaocheng/ Repair or refit the system
7. Turn off network wake-up. On the desktop, right-click computer (my computer) - properties - Device Manager - expand network adapter - right click network card - properties - Advanced - set "off network wake up" to off - power management - remove the check "allow computer to turn off this device to save power"
8. Update hardware drivers such as graphics card and sound card with driver wizard
9. Click "start" on the desktop and select "control panel" to enter; Enter the control panel of the computer, find "system and security" and click to enter; Under "Windows Update" in the interface, there is a "enable or disable automatic update" button. Click to enter. Among the four options of "important update", select "disable automatic update"; After selection, click OK.
1. Set the system error function. Right click my computer - properties - system properties advanced - startup and recovery - Settings - startup and recovery - remove the "auto restart" option in the "system failure" column
2. Check if the main board battery voltage is too low, and replace the battery; Set the BIOS to the factory default
3. Set up power management. Click "start - Settings - control panel - Power Options". In the pop-up window, enable or cancel "advanced power support" as needed. If you use "advanced power support" when a fault occurs, try to cancel it, otherwise, enable it
4. The memory may be damaged or in poor contact, or the memory slot of the motherboard is faulty. Use the eraser to clean the memory slot and replace the memory that is suspected to be faulty
5. If you have a USB device connected to your computer, unplug it first and then turn it off. Or in BIOS, set restore AC power loss of power management setup in BIOS to disabled and PM control by APM of power management setup to yes
6. If the system files are missing, please refer to the system ghost base installation tutorial www.ghost008.com/jiaocheng/ Repair or refit the system
7. Turn off network wake-up. On the desktop, right-click computer (my computer) - properties - Device Manager - expand network adapter - right click network card - properties - Advanced - set "off network wake up" to off - power management - remove the check "allow computer to turn off this device to save power"
8. Update hardware drivers such as graphics card and sound card with driver wizard
9. Click "start" on the desktop and select "control panel" to enter; Enter the control panel of the computer, find "system and security" and click to enter; Under "Windows Update" in the interface, there is a "enable or disable automatic update" button. Click to enter. Among the four options of "important update", select "disable automatic update"; After selection, click OK.
2.
Computer win10 auto restart is because the auto restart option is checked
The specific operation steps are as follows:1. First, right-click the "this computer" application icon on the desktop of the computer, and then click the "properties" option in the pop-up option box
3. The solution steps are as follows:
1. Set the system error function. Right click my computer - properties - system properties advanced - startup and recovery - Settings - startup and recovery - remove the "auto restart" option in the "system failure" column
2. Check if the main board battery voltage is too low, and replace the battery; Set the BIOS to the factory default
3. Set up power management. Click "start - Settings - control panel - Power Options". In the pop-up window, enable or cancel "advanced power support" as needed. If you use "advanced power support" when a fault occurs, try to cancel it, otherwise, enable it
4. The memory may be damaged or in poor contact, or the memory slot of the motherboard is faulty. Use the eraser to clean the memory slot and replace the memory that is suspected to be faulty
5. If you have a USB device connected to your computer, unplug it first and then turn it off. Or in BIOS, set restore AC power loss of power management setup in BIOS to disabled and PM control by APM of power management setup to yes
6. If the system files are missing, please refer to the system ghost base installation tutorial www.ghost008.com/jiaocheng/ Repair or refit the system
7. Turn off network wake-up. On the desktop, right-click computer (my computer) - properties - Device Manager - expand network adapter - right click network card - properties - Advanced - set "off network wake up" to off - power management - remove the check "allow computer to turn off this device to save power"
8. Update hardware drivers such as graphics card and sound card with driver wizard
9. Click start on the desktop and select control panel to enter; Enter the control panel of the computer, find "system and security" and click to enter; Under "Windows Update" in the interface, there is a "enable or disable automatic update" button. Click to enter. Among the four options of "important update", select "disable automatic update"; After selection, click OK.
1. Set the system error function. Right click my computer - properties - system properties advanced - startup and recovery - Settings - startup and recovery - remove the "auto restart" option in the "system failure" column
2. Check if the main board battery voltage is too low, and replace the battery; Set the BIOS to the factory default
3. Set up power management. Click "start - Settings - control panel - Power Options". In the pop-up window, enable or cancel "advanced power support" as needed. If you use "advanced power support" when a fault occurs, try to cancel it, otherwise, enable it
4. The memory may be damaged or in poor contact, or the memory slot of the motherboard is faulty. Use the eraser to clean the memory slot and replace the memory that is suspected to be faulty
5. If you have a USB device connected to your computer, unplug it first and then turn it off. Or in BIOS, set restore AC power loss of power management setup in BIOS to disabled and PM control by APM of power management setup to yes
6. If the system files are missing, please refer to the system ghost base installation tutorial www.ghost008.com/jiaocheng/ Repair or refit the system
7. Turn off network wake-up. On the desktop, right-click computer (my computer) - properties - Device Manager - expand network adapter - right click network card - properties - Advanced - set "off network wake up" to off - power management - remove the check "allow computer to turn off this device to save power"
8. Update hardware drivers such as graphics card and sound card with driver wizard
9. Click start on the desktop and select control panel to enter; Enter the control panel of the computer, find "system and security" and click to enter; Under "Windows Update" in the interface, there is a "enable or disable automatic update" button. Click to enter. Among the four options of "important update", select "disable automatic update"; After selection, click OK.
4.
1. On the windows10 desktop, right-click the computer icon on the desktop and select the "properties" menu item in the pop-up menu
5. The computer restart analysis steps and solutions are as follows:
1. If there is a bad contact between the memory slot on the computer motherboard and the memory, it is easy to cause blue screen, crash and restart. How to deal with it: you can use an eraser to wipe your current memory a few times, that is, where there is a gold finger, that is, where there is a copper chip. After the solution, you can change a memory slot and plug it back in. (of course, if there is a false soldering in the memory display and memory integrated block, it will always restart),
2, Motherboard crash or restart phenomenon is more
3. The operating system of the computer fails, for example, the system loses files. Computer virus
and so on, the solution: refer to the system ghost system base www.ghost008.com/win7/ The problem is solved by reloading the system
4. There is something wrong with the CPU fan on the motherboard, and the CPU can't be cooled down. When the temperature reaches the limit of the CPU, it will automatically restart, so you only need to change the fan, or
because the ash blocks the fan, you can turn it on, and you also need to add silicone grease to the CPU. The role of silicone grease is to make the CPU fan and CPU play a good role in heat dissipation
5. If the computer restarts frequently, 60% of it is caused by the power supply problem. The problem can be solved by replacing the new power supply. It is necessary to replace the power supply above 400W
6. There are too many bad tracks on the hard disk. When the hard disk reads these places, it can't read any more, causing it to jam. After a while, it will crash. The solution is to repair the bad tracks and replace the hard disk
7. Insufficient power supply, impure DC output and slow dynamic response of the chassis are one of the most suspected causes of automatic system restart
8. Right click my computer - properties - Advanced - click settings in "startup and recovery" - remove the check before "auto restart" in "system failure" - OK, restart the computer to see if it can be eliminated.
1. If there is a bad contact between the memory slot on the computer motherboard and the memory, it is easy to cause blue screen, crash and restart. How to deal with it: you can use an eraser to wipe your current memory a few times, that is, where there is a gold finger, that is, where there is a copper chip. After the solution, you can change a memory slot and plug it back in. (of course, if there is a false soldering in the memory display and memory integrated block, it will always restart),
2, Motherboard crash or restart phenomenon is more
3. The operating system of the computer fails, for example, the system loses files. Computer virus
and so on, the solution: refer to the system ghost system base www.ghost008.com/win7/ The problem is solved by reloading the system
4. There is something wrong with the CPU fan on the motherboard, and the CPU can't be cooled down. When the temperature reaches the limit of the CPU, it will automatically restart, so you only need to change the fan, or
because the ash blocks the fan, you can turn it on, and you also need to add silicone grease to the CPU. The role of silicone grease is to make the CPU fan and CPU play a good role in heat dissipation
5. If the computer restarts frequently, 60% of it is caused by the power supply problem. The problem can be solved by replacing the new power supply. It is necessary to replace the power supply above 400W
6. There are too many bad tracks on the hard disk. When the hard disk reads these places, it can't read any more, causing it to jam. After a while, it will crash. The solution is to repair the bad tracks and replace the hard disk
7. Insufficient power supply, impure DC output and slow dynamic response of the chassis are one of the most suspected causes of automatic system restart
8. Right click my computer - properties - Advanced - click settings in "startup and recovery" - remove the check before "auto restart" in "system failure" - OK, restart the computer to see if it can be eliminated.
6. I don't know why. All kinds of instability, or win7 good, good compatibility, it is recommended to change the system
7. Unknown_Error
8.
Hot content