B250 motherboard mining is not on

1. Maybe you need to set BIOS? I don't know about Yingtai's mining motherboard. I haven't used it before. I'm using ms-h87u3 Pro now. This generation of motherboard and u are cheaper and more stable. Mining is easier to use than B250. However, it's stopped proction now. It seems that there is a new replacement proct, ms-b85-btc, with less than 400 pieces

2. The evaluation is as follows, the person stupid money many speed come
now the mining instry is basically collapsing, and it's all the plate takers
sooner or later
if you have to mine, remember to install the original system + driver 7 and update the driver, so that mining can be stable enough.

3. This motherboard is definitely not mining, ASUS b250h-gaming Raptor series motherboard is the main game, how can the motherboard be mining? The special mining motherboard's PCI slot gives you more motherboard, so it will not affect your use and warranty. Don't worry,

4. 1. If you press the power on button of the host, the power light will not be on or will be off once it is on, replace the switching power supply first
2. If the power light is on after the switching power supply is replaced, but it still can't be started, press the num lock key, and the num lock light won't be on. In this case, the motherboard can't start normally. Please shut down, remove the memory, clean the memory golden finger, and then re insert it
3, then check the graphics card, clean the golden finger of the graphics card, re insert the motherboard, and then try to power on. If the keyboard light is on after power on, press num lock key, the corresponding light will also be on, which is basically the problem of the graphics card
4. If the screen is still black, but the display is normal after changing to another monitor, the monitor is damaged and needs to be repaired. If it is the same after replacing the monitor, try to replace the graphics card. If it is normal after replacing the graphics card, the graphics card is damaged and needs to be repaired or replaced
5. If the system just fails to boot, makes an error or has a blue screen, it can be solved by re installing the original system.

5.

Problem analysis:

when the computer is powered on, the main board is powered on, and the display is powered on (the power indicator is on), but there is no signal or "no sighal" is displayed on the screen. Generally, the memory mole is loose or oxidized, resulting in poor contact, or the data line of the display is in poor contact, or the memory, graphics card, display or data line is damaged

processing suggestions:

1. If the display is powered on but no signal is displayed, turn off the power supply (if short pressing the power switch is invalid, long pressing the switch until the power indicator is off or directly unplug the power cord) power off the boot box, plug in the memory mole again, and wipe the golden finger with a rubber in one direction (thumb and fingernail back scraping is also OK), If possible, it can also be installed in different memory slots, and then it can be turned on (before operation, it is necessary to release its own static electricity by touching the wall with both hands or wear anti-static gloves). If you don't know how to operate, it's a little simpler: just slap or kick the chassis once or twice (Note: the right and left side of the chassis are in the center of the shell without interface at the back; Attention: don't push too hard, of course not powerless). The above operation may need to be repeated. If it is invalid, the memory mole needs to be replaced. If there are more than two memory moles, you need to test them one by one

If the above operation is invalid, power off the boot box, plug in the graphics card again, and plug in the data cable between the display and the graphics card tightly. If it is still invalid, consider the data line or graphics card damage, then replace the new data line or graphics card

If the monitor is not powered on (the indicator light is not on), first check whether the power switch is on, then check the back of the monitor, plug the plug of the power cord connecting the monitor upward (replace the power cord if possible), and check whether the other end of the power cord is powered on to the socket

4. If the display can be displayed when the host computer is connected to other displays or the display of the host computer is connected to other normal hosts, it means that the display is damaged and needs professional maintenance

6. Solution:
1. Plug the power cord tightly, check the plug on the plug board, and make sure that the plug board is powered on
2. Make sure that the cable from the host power supply to the board is good, then remove the 24P plug from the power supply to the main board, and short the green and any black wires. If the power fan turns, it means that the power supply is OK. If the power fan doesn't turn, it means that the power supply is broken. Replace it with a new power supply
3. After confirming that there is no problem in the above two steps, unplug the switch cable connecting the main board and the front panel of the chassis, and use a screw driver to short circuit the two pins of the switch. If the fan turns, it means that the main board is OK. If the fan doesn't turn, it means that it is mostly the main board problem. Contact professional maintenance personnel to deal with it
4. Short circuit the pin of the main board, and press the switch button on the front panel, but there is no response. It means that the switch button is broken or stuck. Replace it with a new switch button, or get the stuck button up.

7. The motherboard installation of the independent display is a necessary external hardware, and there is no need to set the upgrade BIOS. Even if 20 pieces of old independent display are installed and 5000 level gtx1080 independent display is removed, there is no need to set the motherboard. Only after the independent display is installed, the rated power of the power supply is sufficient to meet the needs of the host to increase the power consumption of the independent display,
replace the independent display and restart the computer system, Just re install the driver.

8. Win10 operating system shut down first and start quickly. If win10 is not used, it is recommended to install the official version of win10 operating system of Microsoft and use UEFI to quickly start
1. Press Win + X on the desktop and click the power option
2. Click "select power button function" in the left window
3. Select "change the currently unavailable settings"
4. Find to enable quick start and remove the previous check. Save the changes
5, and then try shutting down
note: if normal, you can check the quick start again according to the above method.

9. Now many mainboard's mouse and keyboard are powered by the standby circuit of the mainboard. No matter whether you turn on the computer or not, they all have power as long as you plug in the power supply. If you want to turn them off, you just need to change the jumper on the mainboard to control the mouse and keyboard. I'm sure that's right. Power on: press del continuously to enter the BIOS page. Use the keyboard up, down, left, right to locate the power management setup. Set the USB wake up from S3 to disable. F10 --- yes
turn off the keyboard and mouse power on function in BIOS and turn on the power management setup page in the main menu of BIOS, Find S3 KB wake up function or similar options (such as resume on KBC, resume on PS / 2 mouse, etc.), set it to disable, turn off the + 5VSB power supply of the main board to the keyboard and mouse, and the PS / 2 photoelectric mouse will not light up naturally after it is turned off
there is a jumper on the motherboard. Just change the jumper to another location. The location is probably near the mouse interface. Look for it

10. There is something wrong with the computer. Maybe the hardware is damaged