ASUS motherboard mining settings
Publish: 2021-03-31 00:59:38
1. Recently, the price of bitcoin has been rising. Last week, the single price of bitcoin broke through the RMB 20000 mark. Compared with speculation, what is more exciting is self-sufficient mining. The assembly of mining machine has become the focus of attention
in order to cater to the current mining boom, major manufacturers have released corresponding mining motherboards to seize the market. What can be inserted into the magic board of 13 graphics cards, super stable power supply and so on. It's easy to ignore the BIOS on the motherboard while configuring the heap. Although the current mining has experienced several years of training, but at present, when we assemble the mining machine, we still need to toss BIOS, in order to use the multi card to improve the performance of mining. For most mine friends, it is a great test to brush BIOS. If the brush is broken, the whole board will be scrapped. The major manufacturers in improving the corresponding configuration at the same time, but rarely invest too much research and development in BIOS. The reason is that the BIOS of mining machinery is difficult to develop, the research and development time is too long, and the cost recovery is slow. Therefore, compared with the BIOS of special mining machine, it is better to improve the profit of motherboard configuration
there are many mining motherboards on the market, but there are few motherboards with BIOS specially set for mining. Recently, Meijie has developed a special intelligent BIOS for the newly upgraded professional mining motherboard sy-b85-btc. The BIOS of this motherboard can intelligently identify 6 graphics cards. Save all mine friends time, plug and play, convenient and fast, mining no longer wait. We all know that AMD's mining graphics cards have been sold crazy recently, and NVIDIA can't sit there any more. It is reported that NVIDIA will launch a professional mine card gtx1060, which has no display output interface. Meijie, with foresight, has set up integrated display output for mining BIOS by default. After that, NVIDIA's gtx1060 can be perfectly adapted, more than enough
Meijie sy-b85-btc is based on the scheme design verified by mining instry for many years, and also continues the characteristics of Meijie's high efficiency and low price mine board. As an ATX board, Meijie is equipped with 7-phase luxury power supply, all solid black gold capacitor and PCI-E stabilized capacitor design, to ensure stable and safe mining< The sy-b85-btc adopts B85 chip design, supports the fourth and fifth generation CPU of lga1150 interface, and supports lga115x and LGA775 radiator. It is convenient for miner to upgrade the motherboard and use the old CPU and radiator at the same time. Of course, six PCI-E slots are essential for the motherboard specially designed for mining. Three of them are pci-ex16 slots and three are pci-ex1 slots, which can support up to 6 cards mining. Meijie sy-b85-btc also supports 7 * 24-hour all-weather mining, lightning protection, over-current protection, over-voltage protection, high temperature protection, etc. Such a sharp artifact, how can you not let mining friends heart?
in order to cater to the current mining boom, major manufacturers have released corresponding mining motherboards to seize the market. What can be inserted into the magic board of 13 graphics cards, super stable power supply and so on. It's easy to ignore the BIOS on the motherboard while configuring the heap. Although the current mining has experienced several years of training, but at present, when we assemble the mining machine, we still need to toss BIOS, in order to use the multi card to improve the performance of mining. For most mine friends, it is a great test to brush BIOS. If the brush is broken, the whole board will be scrapped. The major manufacturers in improving the corresponding configuration at the same time, but rarely invest too much research and development in BIOS. The reason is that the BIOS of mining machinery is difficult to develop, the research and development time is too long, and the cost recovery is slow. Therefore, compared with the BIOS of special mining machine, it is better to improve the profit of motherboard configuration
there are many mining motherboards on the market, but there are few motherboards with BIOS specially set for mining. Recently, Meijie has developed a special intelligent BIOS for the newly upgraded professional mining motherboard sy-b85-btc. The BIOS of this motherboard can intelligently identify 6 graphics cards. Save all mine friends time, plug and play, convenient and fast, mining no longer wait. We all know that AMD's mining graphics cards have been sold crazy recently, and NVIDIA can't sit there any more. It is reported that NVIDIA will launch a professional mine card gtx1060, which has no display output interface. Meijie, with foresight, has set up integrated display output for mining BIOS by default. After that, NVIDIA's gtx1060 can be perfectly adapted, more than enough
Meijie sy-b85-btc is based on the scheme design verified by mining instry for many years, and also continues the characteristics of Meijie's high efficiency and low price mine board. As an ATX board, Meijie is equipped with 7-phase luxury power supply, all solid black gold capacitor and PCI-E stabilized capacitor design, to ensure stable and safe mining< The sy-b85-btc adopts B85 chip design, supports the fourth and fifth generation CPU of lga1150 interface, and supports lga115x and LGA775 radiator. It is convenient for miner to upgrade the motherboard and use the old CPU and radiator at the same time. Of course, six PCI-E slots are essential for the motherboard specially designed for mining. Three of them are pci-ex16 slots and three are pci-ex1 slots, which can support up to 6 cards mining. Meijie sy-b85-btc also supports 7 * 24-hour all-weather mining, lightning protection, over-current protection, over-voltage protection, high temperature protection, etc. Such a sharp artifact, how can you not let mining friends heart?
2. There is an m.2 key m interface, so it can be connected to PCI-E devices. With ngff m.2 to PCI-E x16 slot adapter card, you can connect the graphics card, and with the other 6 PCI-E slots, you can realize 7-Card mining, and the bandwidth does not affect the computing power of the graphics card at all. And the motherboard's own workmanship and power supply are quite excellent, mining stability performance is also good.
3.
Now mining can use ha Yu miner , perfectly compatible with this kind of computer equipment, for computer configuration, automatic optimization of computer configuration mining algorithm. A lot of people are already using it
4. 1. Setting and changing the automatic power on function of the host after power on, After power failure (off, on, auto) is the same as above
power loss function (always off,)
AC back function (soft off, paste, full on, memory)
2. Removal of three times of memory check ring startup
quick power on self test (enabled, disabled)
select enabled to allow the computer to start quickly, and only one time of memory check< 3. BIOS chip write protection
flash part write protection (enabled disabled)
flash write protection (enabled disabled)
when you update your motherboard BIOS, this function should be disabled, otherwise you cannot successfully refresh your BIOS code. When your computer hardware changes, this function should also be prohibited in the civilized small stickers of primary school students. Let the system automatically write DMI data into the BIOS chip and then allow this function
4. Intelligent detection of hard disk
HDD. S.m.a.r.t. capability (enabled disabled)
when this function is turned on, if the hard disk fails, the system can prompt you in advance. There may be a problem with the hard disk, please back up your data< When this item is set to yes, if your floppy drive is removed, you can start the system directly without setting the CMOS; My computer & quot; There will be no floppy drive in the system, but no & quot; Removable disk & quot; It's the symbol of the world
6. Boot method setting
power on function (button only, keyboard 98, password, hot key, mouse left, BIOS, mouse right, any key)
this function is to set different boot methods, some need to set jumper on the motherboard. Function options are only power on, keyboard power on key, need to enter a password to power on, a combination of keys, left mouse button, right mouse button, any key to power on
7. PCI graphics card palette function
PCI / VGA palette snoop (disabled, enabled)
BIOS setting, this function is effective for PCI graphics card, if your graphics card does not support the palette function, please disable it, otherwise it is easy to display when entering the system< How to set the BIOS, 8. Virus protection switch
anti virus protection (disabled enabled)
please disable this function when installing the system, because Win98, Win2K and WinXP systems need to rewrite the boot area of the hard disk when installing. If this function is allowed, the system will crash. Usually, this function can be turned on to prevent the virus from damaging the hard disk data. When a virus or other program suddenly writes to the MBR area and boot area of the hard disk, the system will pop up a white and black window to prompt you that there is a program ready to write to the hard disk. Is it allowed? If allowed, you have to press y twice to confirm
9. Init display first (PCI slot, AGP slot, onboard AGP)
if your system has more than one graphics card, you can choose which graphics card will display first according to the BIOS setting before entering the system
10. Select the key function of power on
soft off by pwr-bttn (instant off, delay 4 second)
this function is the way to set the power on / off key: immediately shut down and delay 4S shut down
11. Remove the information of network card startup item when power on
Press Shift + F10 to enter the network card setting menu and disable the information display item
12. Memory hole at 15m-16m
this option allows you to reserve the corresponding area in the system memory for the ROM of ISA card. When the region is reserved, it cannot be cached. Computer peripherals have corresponding areas in memory to store their related information. Options: enabled, BIOS Setup tutorial, disabled
power loss function (always off,)
AC back function (soft off, paste, full on, memory)
2. Removal of three times of memory check ring startup
quick power on self test (enabled, disabled)
select enabled to allow the computer to start quickly, and only one time of memory check< 3. BIOS chip write protection
flash part write protection (enabled disabled)
flash write protection (enabled disabled)
when you update your motherboard BIOS, this function should be disabled, otherwise you cannot successfully refresh your BIOS code. When your computer hardware changes, this function should also be prohibited in the civilized small stickers of primary school students. Let the system automatically write DMI data into the BIOS chip and then allow this function
4. Intelligent detection of hard disk
HDD. S.m.a.r.t. capability (enabled disabled)
when this function is turned on, if the hard disk fails, the system can prompt you in advance. There may be a problem with the hard disk, please back up your data< When this item is set to yes, if your floppy drive is removed, you can start the system directly without setting the CMOS; My computer & quot; There will be no floppy drive in the system, but no & quot; Removable disk & quot; It's the symbol of the world
6. Boot method setting
power on function (button only, keyboard 98, password, hot key, mouse left, BIOS, mouse right, any key)
this function is to set different boot methods, some need to set jumper on the motherboard. Function options are only power on, keyboard power on key, need to enter a password to power on, a combination of keys, left mouse button, right mouse button, any key to power on
7. PCI graphics card palette function
PCI / VGA palette snoop (disabled, enabled)
BIOS setting, this function is effective for PCI graphics card, if your graphics card does not support the palette function, please disable it, otherwise it is easy to display when entering the system< How to set the BIOS, 8. Virus protection switch
anti virus protection (disabled enabled)
please disable this function when installing the system, because Win98, Win2K and WinXP systems need to rewrite the boot area of the hard disk when installing. If this function is allowed, the system will crash. Usually, this function can be turned on to prevent the virus from damaging the hard disk data. When a virus or other program suddenly writes to the MBR area and boot area of the hard disk, the system will pop up a white and black window to prompt you that there is a program ready to write to the hard disk. Is it allowed? If allowed, you have to press y twice to confirm
9. Init display first (PCI slot, AGP slot, onboard AGP)
if your system has more than one graphics card, you can choose which graphics card will display first according to the BIOS setting before entering the system
10. Select the key function of power on
soft off by pwr-bttn (instant off, delay 4 second)
this function is the way to set the power on / off key: immediately shut down and delay 4S shut down
11. Remove the information of network card startup item when power on
Press Shift + F10 to enter the network card setting menu and disable the information display item
12. Memory hole at 15m-16m
this option allows you to reserve the corresponding area in the system memory for the ROM of ISA card. When the region is reserved, it cannot be cached. Computer peripherals have corresponding areas in memory to store their related information. Options: enabled, BIOS Setup tutorial, disabled
5. I want you to read the manual carefully
there are pictures to see. You can't send pictures here
the specific position is that there are two rows of needles and 18 feet at the most corner of the board
power light buzzer
|_|_______|_____|<
123456789
123456789
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -_ LED power indicator
HDD Hard Disk jumper
HDD_ Led hard disk indicator light jumper
reset key jumper
speaker jumper
so it's best to read the manual to complete the operation
there are pictures to see. You can't send pictures here
the specific position is that there are two rows of needles and 18 feet at the most corner of the board
power light buzzer
|_|_______|_____|<
123456789
123456789
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -_ LED power indicator
HDD Hard Disk jumper
HDD_ Led hard disk indicator light jumper
reset key jumper
speaker jumper
so it's best to read the manual to complete the operation
6. Motherboard BIOS update and enter the best settings can be (motherboard models are different). The specific guidance is set again.
7.
1. Start the machine and press the "del" key immediately when entering the first interface to enter the interface
8. Although BIOS setting is not a profound thing, my brother who is not good at e-writing still feels dizzy at first. I'll give you a detailed illustration in Chinese. I believe it will be useful for you to take a serious look. However, this is the old version of BIOS setting. If my friend's machine is a new one after 2008, there is no need to look at it, Please read another article about setting for the new version: the new version of ASUS BIOS setting
Basic Input Output System: basic input output system
setting program is a set of programs solidified into the ROM chip on the computer motherboard. Its main function is to provide the lowest level and most direct hardware setting and control for the computer. The BIOS Setup program is stored in the BIOS chip and can be set only when the computer is turned on. CMOS is mainly used to store the parameters and data set by the BIOS Setup program, and the BIOS Setup program is mainly used to manage and set the basic input and output system of skills, so that the system runs in the best state. Using the BIOS Setup program can also eliminate system faults or diagnose system problems
according to different manufacturers, BIOS programs used on our computers can be divided into award BIOS program, AMI BIOS program, Phoenix BIOS program, other jumper free BIOS programs and BIOS programs unique to brand computers, such as IBM, etc
at present, there are three types of BIOS on motherboard, namely award AMI and Phoenix. However, Phoenix has merged award, so in terms of desktop motherboard, although it is marked with award-phoenix, it is actually the BIOS of award. Phoenix BIOS is mostly used in high-end 586 original brand computers and laptops, and its picture is simple and easy to operate
the following boot is the hard disk setting, and the first group of IDE master devices of primary master exist in the list; Primary slave the first group of IDE slaves; The second group of IDE master devices; Second slave the second group of IDE slaves. The IDE devices here include IDE hard disk and IDE optical drive. The first and second groups of devices refer to the first and second ide data lines on the motherboard. Generally speaking, the first group of IDE devices is close to the chip, while the master device and slave device refer to two devices connected on one ide data line. We know that each data line can be connected to two different devices, the master device and the slave device The slave device can be adjusted by the jumper at the back of the hard disk or optical drive
the following is the type and hardware parameters of IDE device. Type is used to describe the type of hard disk device. We can select the working modes of auto, user and none. The system detects the type of hard disk by itself and stores 1-45 types of hard disk parameters in the system. When using this setting value, it is unnecessary to set other parameters; If the hard disk we use is not predefined, we should set the hard disk type to user, and then input the actual parameters of the hard disk (these parameters are generally on the surface label of the hard disk); If no ide device is installed, we can select the none parameter to speed up the startup of the system. In some special operations, we can also shield the system from automatically checking some hard disks
size indicates the capacity of the hard disk; Cyls hard disk cylinder number; Number of heads of head hard disk; Precomp writes precompensation value; LANDZ landing area is the start stop sector of the magnetic head. The last mode is the working mode of hardware. We can choose normal mode, LBA logic block address mode, large hard disk mode and auto selection mode. Normal mode is the original ide mode. In this mode, you can access the BIOS of hard disk and IDE controller to make any conversion to the parameter part. The maximum capacity supported is 528mb. The maximum capacity of hard disk managed by LBA mode is 8.4GB, and that supported by large mode is 1GB. Auto mode is the working mode of hard disk automatically selected by the system
the other parts in Figure 2 are drive a and drive b floppy drive settings. If there is no drive B, then none drive B is set. We can choose our floppy drive type here. Of course, in most cases, we don't have to change this setting
video setting is used to set the working mode of the monitor, that is, EGA / VGA working mode
halt on this is an error stop setting. All errors BIOS: it will stop when any error is detected; No errors: when BIOS detects any non serious errors, the system will not stop; All but keyword: except for the keyboard error, any error detected by the system will be stopped; All but disable: except for the disk drive error, the system will shut down if it detects any error; All but disk / key: except for disk drive and keyboard errors, any error detected by the system will be stopped. This is used to set the shutdown mode of system self-test. If the above error occurs, the system will stop starting and give an error prompt
we can notice that in the bottom right of Figure 2, there are parameters of system memory: base memory: basic memory; Extended extended memory; Other memory; Total memory
BIOS features setup Figure 3
enabled is on and disabled is disabled. Page up and page down can be used to switch between the two
CPU internal core speed: the current running speed of CPU
virus warning: virus warning
CPU internal / external cache
CPU L2 gache ECC checking
quick power on self test (quick power on self test) this option can be used to adjust the self test steps of some computers to check the memory capacity three times ring self test
CPU update data
boot from LAN first this option can wake up the computer remotely
boot sequence is a function that we often adjust. We usually use a, C, SCSI and CDROM in the order. If you need to boot from CD, you can adjust it to only CDROM. For normal operation, it's better to start from CD.
BIOS false protection (BIOS write protection)
processor serial number (the system automatically detects Pentium 3 processor)
swap floppy drive
VGA boot from
boot up floppy seek
boot up NumLock status
typematic rate setting
typematic rate (chars / sec, byte / sec)
type delay (setting the first delay time)
if the security option is set to setup, the screen will prompt you to enter the password every time you open the machine (ordinary user password or super user password, ordinary users have no right to modify BIOS settings), and if you don't know the password, you can't use the machine; If it is set to system, the user will be prompted to enter the super user password only when he wants to enter the BIOS settings
memory parity check: if the memory mole configured on the machine does not have parity check function, it must be set to disable. At present, except for the server, most microcomputers (including brand computers) do not have parity check in their memory.
standard CMOS setup: Standard CMOS settings include date and time settings, Here you can set the time and date on your computer
PCI / VGA palette snoop (color correction)
assign IRQ for VGA IRQ is the system interrupt address< br />OS SELECT FOR DRAM> 64MB (set the memory capacity of OS2) if the OS / 2 system is in use and the system memory is larger than 64MB, this item should be enabled. Otherwise, the memory higher than 64MB cannot be used, and it is generally disabled
HDD s.m.a.r.t. capability this option can be used to automatically detect the performance of the hard disk. If the hard disk is about to be damaged, the hard disk self-test program will give an alarm
report no FDD for Win95 (assign irq6 to FDD) FDD is a floppy drive
Video BIOS show (VGA BIOS show) is used to improve the display speed of the system. It is usually turned on. C8000-cbffff shadow: this area is mainly used to map the ROM content on the expansion card (network card, decompression card, etc.) and put it into the host ram to run, so as to improve the speed<
(the whole process diagram of the latest AMI BIOS settings)
here are the advanced settings for setting plug and play and PCI. Generally, users do not need to change any items, just keep the default. In this setting, incorrect value will cause system damage< USB configuration (USB device setting)
BIOS has not written data for a long time. Today, some friends searched the Internet and found an article in crazy song prodigal son. Just post it recently... (basic input output system) the setup program is a set of programs that are solidified into the ROM chip on the computer motherboard, Its main function is to provide the most direct hardware setting and control for the computer. The BIOS Setup program is stored in the BIOS chip and can be set only when the computer is turned on. CMOS is mainly used to store the parameters and data set by the BIOS Setup program, and the BIOS Setup program is mainly used to manage and set the basic input and output system of skills, so that the system runs in the best state. Using the BIOS Setup program can also eliminate system faults or diagnose system problems
according to different manufacturers, BIOS programs used on our computers can be divided into award BIOS program, AMI BIOS program, Phoenix BIOS program, other jumper free BIOS programs and BIOS programs unique to brand computers, such as IBM, etc
at present, there are three types of BIOS on motherboard, namely award AMI and Phoenix. However, Phoenix has merged award, so in terms of desktop motherboard, although it is marked with award-phoenix, it is actually the BIOS of award. Phoenix BIOS is mostly used in high-end 586 original brand computers and laptops, and its picture is simple and easy to operate< Standard CMOS setup is used to set the date, time, hard disk specification, working type and display type.
BIOS features setup is used to set the special functions of BIOS, such as virus warning, anti-virus and anti-virus It is used to set the parameters related to CPU operation.
power management setup.
it is used to set the CPU, hard disk, power saving function Power saving function of display and other devices
PNP / PCI configuration
used to set the interrupt and other difference of ISA and other plug and play devices
Load BIOS defaults
this option is used to load the initial BIOS settings
Load option settings
this option is used to load the BIOS settings It is the most basic setting of BIOS, It is used to determine the fault range
integrated peripherals
mainboard integrated device setting
hypervisor password
computer administrator setting to enter BIOS to modify setting password
user password
setting boot password
ide HDD auto detection
Basic Input Output System: basic input output system
setting program is a set of programs solidified into the ROM chip on the computer motherboard. Its main function is to provide the lowest level and most direct hardware setting and control for the computer. The BIOS Setup program is stored in the BIOS chip and can be set only when the computer is turned on. CMOS is mainly used to store the parameters and data set by the BIOS Setup program, and the BIOS Setup program is mainly used to manage and set the basic input and output system of skills, so that the system runs in the best state. Using the BIOS Setup program can also eliminate system faults or diagnose system problems
according to different manufacturers, BIOS programs used on our computers can be divided into award BIOS program, AMI BIOS program, Phoenix BIOS program, other jumper free BIOS programs and BIOS programs unique to brand computers, such as IBM, etc
at present, there are three types of BIOS on motherboard, namely award AMI and Phoenix. However, Phoenix has merged award, so in terms of desktop motherboard, although it is marked with award-phoenix, it is actually the BIOS of award. Phoenix BIOS is mostly used in high-end 586 original brand computers and laptops, and its picture is simple and easy to operate
the following boot is the hard disk setting, and the first group of IDE master devices of primary master exist in the list; Primary slave the first group of IDE slaves; The second group of IDE master devices; Second slave the second group of IDE slaves. The IDE devices here include IDE hard disk and IDE optical drive. The first and second groups of devices refer to the first and second ide data lines on the motherboard. Generally speaking, the first group of IDE devices is close to the chip, while the master device and slave device refer to two devices connected on one ide data line. We know that each data line can be connected to two different devices, the master device and the slave device The slave device can be adjusted by the jumper at the back of the hard disk or optical drive
the following is the type and hardware parameters of IDE device. Type is used to describe the type of hard disk device. We can select the working modes of auto, user and none. The system detects the type of hard disk by itself and stores 1-45 types of hard disk parameters in the system. When using this setting value, it is unnecessary to set other parameters; If the hard disk we use is not predefined, we should set the hard disk type to user, and then input the actual parameters of the hard disk (these parameters are generally on the surface label of the hard disk); If no ide device is installed, we can select the none parameter to speed up the startup of the system. In some special operations, we can also shield the system from automatically checking some hard disks
size indicates the capacity of the hard disk; Cyls hard disk cylinder number; Number of heads of head hard disk; Precomp writes precompensation value; LANDZ landing area is the start stop sector of the magnetic head. The last mode is the working mode of hardware. We can choose normal mode, LBA logic block address mode, large hard disk mode and auto selection mode. Normal mode is the original ide mode. In this mode, you can access the BIOS of hard disk and IDE controller to make any conversion to the parameter part. The maximum capacity supported is 528mb. The maximum capacity of hard disk managed by LBA mode is 8.4GB, and that supported by large mode is 1GB. Auto mode is the working mode of hard disk automatically selected by the system
the other parts in Figure 2 are drive a and drive b floppy drive settings. If there is no drive B, then none drive B is set. We can choose our floppy drive type here. Of course, in most cases, we don't have to change this setting
video setting is used to set the working mode of the monitor, that is, EGA / VGA working mode
halt on this is an error stop setting. All errors BIOS: it will stop when any error is detected; No errors: when BIOS detects any non serious errors, the system will not stop; All but keyword: except for the keyboard error, any error detected by the system will be stopped; All but disable: except for the disk drive error, the system will shut down if it detects any error; All but disk / key: except for disk drive and keyboard errors, any error detected by the system will be stopped. This is used to set the shutdown mode of system self-test. If the above error occurs, the system will stop starting and give an error prompt
we can notice that in the bottom right of Figure 2, there are parameters of system memory: base memory: basic memory; Extended extended memory; Other memory; Total memory
BIOS features setup Figure 3
enabled is on and disabled is disabled. Page up and page down can be used to switch between the two
CPU internal core speed: the current running speed of CPU
virus warning: virus warning
CPU internal / external cache
CPU L2 gache ECC checking
quick power on self test (quick power on self test) this option can be used to adjust the self test steps of some computers to check the memory capacity three times ring self test
CPU update data
boot from LAN first this option can wake up the computer remotely
boot sequence is a function that we often adjust. We usually use a, C, SCSI and CDROM in the order. If you need to boot from CD, you can adjust it to only CDROM. For normal operation, it's better to start from CD.
BIOS false protection (BIOS write protection)
processor serial number (the system automatically detects Pentium 3 processor)
swap floppy drive
VGA boot from
boot up floppy seek
boot up NumLock status
typematic rate setting
typematic rate (chars / sec, byte / sec)
type delay (setting the first delay time)
if the security option is set to setup, the screen will prompt you to enter the password every time you open the machine (ordinary user password or super user password, ordinary users have no right to modify BIOS settings), and if you don't know the password, you can't use the machine; If it is set to system, the user will be prompted to enter the super user password only when he wants to enter the BIOS settings
memory parity check: if the memory mole configured on the machine does not have parity check function, it must be set to disable. At present, except for the server, most microcomputers (including brand computers) do not have parity check in their memory.
standard CMOS setup: Standard CMOS settings include date and time settings, Here you can set the time and date on your computer
PCI / VGA palette snoop (color correction)
assign IRQ for VGA IRQ is the system interrupt address< br />OS SELECT FOR DRAM> 64MB (set the memory capacity of OS2) if the OS / 2 system is in use and the system memory is larger than 64MB, this item should be enabled. Otherwise, the memory higher than 64MB cannot be used, and it is generally disabled
HDD s.m.a.r.t. capability this option can be used to automatically detect the performance of the hard disk. If the hard disk is about to be damaged, the hard disk self-test program will give an alarm
report no FDD for Win95 (assign irq6 to FDD) FDD is a floppy drive
Video BIOS show (VGA BIOS show) is used to improve the display speed of the system. It is usually turned on. C8000-cbffff shadow: this area is mainly used to map the ROM content on the expansion card (network card, decompression card, etc.) and put it into the host ram to run, so as to improve the speed<
(the whole process diagram of the latest AMI BIOS settings)
here are the advanced settings for setting plug and play and PCI. Generally, users do not need to change any items, just keep the default. In this setting, incorrect value will cause system damage< USB configuration (USB device setting)
BIOS has not written data for a long time. Today, some friends searched the Internet and found an article in crazy song prodigal son. Just post it recently... (basic input output system) the setup program is a set of programs that are solidified into the ROM chip on the computer motherboard, Its main function is to provide the most direct hardware setting and control for the computer. The BIOS Setup program is stored in the BIOS chip and can be set only when the computer is turned on. CMOS is mainly used to store the parameters and data set by the BIOS Setup program, and the BIOS Setup program is mainly used to manage and set the basic input and output system of skills, so that the system runs in the best state. Using the BIOS Setup program can also eliminate system faults or diagnose system problems
according to different manufacturers, BIOS programs used on our computers can be divided into award BIOS program, AMI BIOS program, Phoenix BIOS program, other jumper free BIOS programs and BIOS programs unique to brand computers, such as IBM, etc
at present, there are three types of BIOS on motherboard, namely award AMI and Phoenix. However, Phoenix has merged award, so in terms of desktop motherboard, although it is marked with award-phoenix, it is actually the BIOS of award. Phoenix BIOS is mostly used in high-end 586 original brand computers and laptops, and its picture is simple and easy to operate< Standard CMOS setup is used to set the date, time, hard disk specification, working type and display type.
BIOS features setup is used to set the special functions of BIOS, such as virus warning, anti-virus and anti-virus It is used to set the parameters related to CPU operation.
power management setup.
it is used to set the CPU, hard disk, power saving function Power saving function of display and other devices
PNP / PCI configuration
used to set the interrupt and other difference of ISA and other plug and play devices
Load BIOS defaults
this option is used to load the initial BIOS settings
Load option settings
this option is used to load the BIOS settings It is the most basic setting of BIOS, It is used to determine the fault range
integrated peripherals
mainboard integrated device setting
hypervisor password
computer administrator setting to enter BIOS to modify setting password
user password
setting boot password
ide HDD auto detection
9.
After the ASUS motherboard can be turned on, click del to enter the BIOS interface
after entering the BIOS interface, you can restore the BIOS factory settings in the following two ways:
1. Click F9 and the following interface will appear. Press enter
after restoring the default settings, click F10 to save and exit the BIOS interface
Hot content