Drawing of mining machine

1.

The mining pictures are as follows:

4. It's a chicken to set this up.. Because it may break down, but it's more useful than manual work
this is a of my own
this method will make you hang up longer.. But it doesn't have to work
so
first, open the basic settings in the assistant and let it return to the default
if you haven't used the assistant, turn it on and then turn it off.. Will be automatically set to default
then unload all the equipment
next, choose a place... It's important< br /> I found that when the screen can see the ore has been mined out, there is no way to normal automatic mining.. So it's very important to choose a place that is not too big to ensure that the ore is refreshed
this is usually the lowest part of the mining area or a small platform far from the ground
if it is the former, it will be less likely to stop hanging at any place.. The latter almost never stops
finally, light up the pet's auto picking skill.. And keep other columns free
start automatic mining.

5.

Other tools needed for the use of mining machine: Mining bit, OV or od scanner

1. After preparing the above tools, power on the mining machine

2. Put the drill bit, mining pipe and OD scanner into the position of the mining machine interface as shown in the figure below. When the power supply of the mining machine is enough, mining will begin

note: before the scanner, set the blacklist (that is, you don't want to collect) or white list (ore must be put in it), and then select accurate collection or inaccurate collection

extended data

mining machine is a kind of automatic vertical mining machine. Placing a box beside you can automatically put the collected items into the box. The power consumption of mining opportunities varies according to the internal components (one-time excavation) - mining bits: 450eu ~ 470eu

diamond bit: 880eu ~ 900eu; Od detector: 45eu ~ 75eu; OV detector: 165eu ~ 190eu. The maximum input voltage is 32eu / T, which will explode. The components in the mining machine include: drill, scanner and mining pipe. The number of pipes will be greater than or equal to 1. None of the three components will work without one

6. Now mining is very difficult, and the investment is very large. You can register your wallet to buy and sell bitcoin to earn the price difference. It's a private message

7. Specific configuration process:
1. Open stm32cubemx and select the corresponding chip< The chip in this paper is stm32f207vct6, after selection:
2, configure RCC clock, ETH, PA8 and enable LwIP
as the hardware of the development board here is RMII mode, eth-rmii is selected. If you have a development board in MII mode, please refer to the configuration method of MII. This is only for RMII
RCC selects an external clock source and checks mco1. The software will automatically configure PA8 to mco1 mode. This pin is very important for RMII mode and is used to provide 50MHz clock for PHY chip
enable LwIP
3. The configuration of the clock tree must ensure that the mco1 output is 50MHz. If the frequency is not correct, the PHY chip will not work
here, because the chip is 207vct6, in order to make the mco1 output 50MHz, some adjustments of PLL frequency doubling parameters are made, as follows: (comrades can flexibly configure according to their own chip, but they need to ensure that the mco1 output is 50MHz)
4. Parameter settings of eth, LwIP and RCC
at this point, the more important thing is in the front, but there is still one thing to pay attention to, that is, the output speed of PA8 pin, which failed several times because this pin did not pay attention to
the subsequent parameter settings can be set according to the comrades' own needs, and the settings are given here for reference
the ETH parameter remains the default, but interrupt is checked once
LwIP parameters are set as follows: (because UDP server is configured and IP is allocated statically)
5. Generate the project and make the final function modification
Add UDP server initialization, port binding and other related functions to the generated project
here, the UDP server file in the previous official routine is directly added, as follows:
after that, the UDP server file is added
C file is added to the user program, and UDP is added to the main function
H header file
as follows: (the specific content of the UDP file is given later)
6. Several functions need to be added to the main function. Here, we will not explain the function and implementation principle, but only add them.