Yingchi 1080ti mining

1. Lightcoin is 1.8g. The computing power of the whole network is only 8600gh / s, and 1080ti graphics card occupies 1 / 4700
eth is only 32mh / s, 1070 has 40mh / s. Many people say that 1080ti can't pull up the computing power because of the high delay of gddr5x video memory. As expected, it's better to mine with a card. People on the Internet say that 480 can have 65mh / S computing power
Zec, 724sol / s, nearly three 1060 3G, the total price is more expensive than three 1060 2K soft coins. However, compared with the short supply a-card rx4808g, the price of three cards is less than 5K, and the computing power is 900 + sol / s, but it's useless if there is a price but no market
it's too wasteful to use this card for mining. It's just for fun and can't afford to hurt.

2. If you can't get back to mine for a few months,
1, find a mining website registration account
2, Download mining software, and then you can start
3. If you want to know how much money you can earn, first calculate the hash value of your own graphics card
4, and remind you that the graphics card needs to work hard for a long time, so it's not cost-effective to dig

3. The family does not have a special miner, so it is not cost-effective to mine. The income is not enough to cover the electricity bill. Unless you don't need to pay for electricity, it must be more cost-effective for a single card to consume electricity.
even in professional mining places, many of them bring their own hydropower.

4. The 1080ti of tearing force fish has no invoice, and the 1080 are all mine cards. You haven't seen 1080 from 1450. In fact,
from 1050ti to 1080T is 1065. 750t, 970, 980, 980ti. He who knows knows knows. I say a few words, power station Sichuan Cheng Dashan you all know

5. The axial force of concrete support is calculated according to the compression bearing capacity of normal section. There are relevant calculation regulations in the concrete structure design codes of relevant instries, which are generally the axial compressive strength of concrete multiplied by the cross-sectional area, the compressive strength of steel multiplied by the total cross-sectional area of steel, and then multiplied by a stability factor
I hope I can help you.

6. It depends on the family conditions. If the family conditions are good, you can go to the confinement center. If the family condition is general, if there is someone in the family to take care of you, you can not go. If there is no one to take care of you, you can spend tens of thousands of yuan to the confinement center.

7. How to allow conditions, accept professional care, is certainly better for the mother and baby.

8. The reasons for monitoring the axial force of support in deep foundation pit are as follows:
the foundation pit is generally supported by continuous wall (pile) and steel support, and the axial force of support is a necessary item. Support axial force monitoring is used to monitor the change of support axial force in the construction process of foundation pit, so as to avoid the support failure caused by the support axial force exceeding the design strength and the instability of the whole support system<

monitoring method of supporting axial force:
the multi-functional reading instrument is used for measurement. Generally, the cable of the axial force meter is divided into red and black. First turn on the reading instrument, switch the instrument mode to f mode, and clamp the red clamp of the reading instrument to the red cable line of the axial force meter, and clamp the Black clamp to the black cable line, Read the F value on the display screen of the reader and make a record.

9. The main reasons are: 1
2
the foundation pit is generally supported by continuous wall (pile) and steel support, and the axial force of support is a necessary item. Support axial force monitoring is used to monitor the change of support axial force in the construction process of foundation pit, so as to avoid the support failure caused by the support axial force exceeding the design strength and the instability of the whole support system
calculation of preloaded axial force of steel support in deep foundation pit:
firstly, add the preload to zero to calculate an anchor cable tension, which can ensure the stability of foundation pit against overturning, and then multiply it by 70 ~ 95% of the specification to get the preload
the preload is generally less than 450kn, because most of the pile anchor structures are sand, silt, or clay, and the uplift resistance of this stratum and anchor cable is limited. The preload of 450kn means that the design tension reaches 450 / 0.95 ~ 450 / 0.7, which is basically the limit of ordinary anchor cable in this kind of stratum. If it can not meet the requirement, it is necessary to consider densifying the anchor cable spacing
the prestress loss of the anchor cable in the soil layer is amazing. The 10-15% over tension locking required in the specification is not enough. In fact, the prestress in the soil layer is graally lost from the moment when the jack leaks oil. There are many problems, such as the problem of anchorage and soil creep in the anchorage section. The prestress loss after locking is very terrible. So generally, the preload will not be added, because the actual effect is not as big as that of design and locking.

10. Hello
the maximum value of axial force can be divided into positive and negative: positive tension, which proces tensile stress; Negative pressure proces compressive stress
for plastic materials (mostly steel and other metal materials), because their compressive capacity is much greater than the tensile capacity, only tensile stress is calculated in strength calculation; For brittle materials such as cast iron and concrete, the tensile and compressive capacities are almost the same, and the tensile and compressive stresses need to be calculated in strength calculation
if you have any questions, please ask.