How can Abel mining WiFi log in

1. It's easy to use, saberlili's skill must hit 220% of the damage is very high. Treasure with a little bit, but 9 Dodge is also good
Xijie skill, that is, the half blood second kill under 15 defenses, and passive with 3 kings, 2 kings with treasure, 4 dodge and 3 attack first, is very strong
combination skill 13 attack first,
later, these two people can provide 16 attack first, 5 kings, 13 Dodge, only two people provide so many attributes, the skill is not bad. Very easy to use
hope to adopt

2. You can just click the plus sign on the top with wechat, add friends, search and other money shopping malls

3. Mining always fails. What should we do? This must be looked for.

4. Abel currency login can't go up, the official website also can't open, this may be caused by the software itself, suggest consulting the software customer service

5. Check this way:
1. Dial the operator's customer service number to see if there is any problem with the Internet< Second, plug the cable again.
the cable from the cat is connected to the WAN port of the wireless router, and the computer is connected to any LAN port of the wireless router
Third, turn off the cat and the wireless router, and then turn them on. Take a look later
4. If not, reset the wireless router< Do you want to plug in the wireless router, do not pick up the cat, reset the wireless router (restore the factory), connect the computer to any LAN port of the wireless router, enter the gateway address of the router in the browser address bar (which is on the label on the back of the router), and enter the settings page, According to PPPoE (ADSL virtual dial-up) mode can be set
then set SSID, encryption method and password. Save and restart
after setting, connect the cable from the cat LAN port to the WAN port of the wireless router.

6.

Reason 1: incorrect configuration of wireless router

solution:

suppose that the IP of the router is 192.168.1.1, please refer to the label or instruction manual on the router box

1) one end of the network cable is connected to the LAN port of the router, and the other end is connected to the network port of the computer

2) open the browser, enter 192.168.1.1 (the IP address of the router), and enter the router account number and password (see the label or instruction on the router box)

Internet access: PPPoE

Internet account and password: input broadband account and password

click next

3) wireless status: on

SSID: enter the wireless device name

Channel: select 1 or 6 or 9 (if connecting to Apple mobile device or Mac: select 11 or 13)

note: because channel 1 or 6 or 9 has the least interference, and because Apple mobile devices or Macs support high-frequency channels, select 11 or 13

PSK password: input wireless password

other defaults are OK

4) after setting, one end of the network cable is connected to the LAN port of the cat, and the other end is connected to the WAN port of the wireless router

reason 2: the wireless network card does not support the default wireless channel

solution:

suppose that the IP of the router is 192.168.1.1, please refer to the label or instructions on the router box

1. Open the browser, enter 192.168.1.1 (the IP address of the router), and enter the router account number and password (see the label or instructions on the router box)

2. Take TP-LINK as an example, click Wireless Settings - basic settings, right channel: select 1 or 6 or 9

because the signal interference of channel 1 or 6 or 9 is minimal

reason 3: unable to automatically obtain IP

solution:

assumption: router IP is 192.168.1.1, please refer to the label or instruction manual on the router box for details

1. Click the network logo in the lower right corner, right-click and select open network and sharing center

2. Click [wireless network connection]

3. Point [attribute]

4. Select Internet Protocol version 4 (TCP / IPv4) and click properties

5. Select [use the following IP address]

IP address: 192.168.1.100 (192.168.1.2 ~ 192.168.1.254)

subnet mask: 255.255.255.0

Default Gateway: 192.168.1.1

select [use DNS server address below]

preferred DNS server: 192.168.1.1 (regional general DNS can also be filled in)

standby DNS server: optional

points were determined

7. You will log in to the previous account number, send a verification code with your mobile phone number, and then you can log in directly.

8. Restore the wireless router to the factory settings, and then reset it
the mobile phone can set up a wireless router
if you need to dial a broadband cat to connect to the wireless router, follow the following method:
1. Plug in the wireless router, do not connect the cat, and connect the mobile phone to the wireless network of the wireless router
2. In the browser address bar, enter the router gateway address (which is on the label behind the router), and enter the login user name and password to enter the settings page
3. Set according to PPPoE (ADSL virtual dial-up) mode, input internet account and password
4. Set SSID, encryption method and password
5. Save and restart
6. After setting, connect the cable from the cat LAN port to the WAN port of the wireless router.

9. Program error, see the error prompt means that the certificate has expired
this needs to be modified by the program provider. As a user, there is no way to do it.

10. Start - run - ipconfig / all to check if your IP address is a public IP
try setting a public IP
in addition, check the settings of the tunnel port on the device